SDS
41-6620 WEATHERSCREEN EXTERIOR LATEX SATIN-WHITE
Product name
1
Product code
Date of issue
Version
00408071
7 June 2015
Accidental release measures
6 .
Stop leak if without risk. Move containers from spill area. Approach release from
upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash
spillages into an effluent treatment plant or proceed as follows. Contain and collect
spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or
diatomaceous earth and place in container for disposal according to local regulations
(see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated
absorbent material may pose the same hazard as the spilled product. Note: see Section
1 for emergency contact information and Section 13 for waste disposal.
Large spill
:
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up
if water-soluble or absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Small spill
:
Store in accordance with local regulations. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials
(see Section 10) and food and drink. Keep container tightly closed and sealed until
ready for use. Containers that have been opened must be carefully resealed and kept
upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. Do not store below the following
temperature: 32F / 0C.
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and
smoking should be prohibited in areas where this material is handled, stored and
processed. Persons with a history of skin sensitization problems should not be
employed in any process in which this product is used. Do not swallow. Do not get in
eyes or on skin or clothing. Avoid breathing vapor or mist. Use only with adequate
ventilation. Wear appropriate respirator when ventilation is inadequate. Keep in the
original container or an approved alternative made from a compatible material, kept
tightly closed when not in use. Empty containers retain product residue and can be
hazardous. Do not reuse container. If this material is part of a multiple component
system, read the Material Safety Data Sheet(s) for the other component or components
before blending as the resulting mixture may have the hazards of all of its parts.
Handling and storage
Handling
Storage
:
:
7 .
Exposure controls/personal protection
8 .
Engineering measures
:
Use only with adequate ventilation. If user operations generate dust, fumes, gas, vapor
or mist, use process enclosures, local exhaust ventilation or other engineering controls
to keep worker exposure to airborne contaminants below any recommended or statutory
limits.
Recommended monitoring
procedures
:
If this product contains ingredients with exposure limits, personal, workplace
atmosphere or biological monitoring may be required to determine the effectiveness of
the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to appropriate monitoring standards.
Reference to national guidance documents for methods for the determination of
hazardous substances will also be required.
titanium dioxide
TWA
10 mg/m³
10 mg/m³ TD
10 mg/m³ (as
Ti)
Not established
STEL
Not established
Not established
20 mg/m³ (as
Ti)
Not established
____________________________
___________
___________
___________
___________
___________
ethanediol
STEL
100 mg/m³ C
100 mg/m³ C
100 mg/m³ C
Not established
____________________________
___________
___________
___________
___________
___________
Diatomaceous earth
TWA
Not established
3 mg/m³ R
10 mg/m³
Not established
10 mg/m³
3 mg/m³
____________________________
___________
___________
___________
___________
___________
Name
Result
ACGIH
Ontario
Mexico
PPG
Page: 3/7
Canada - Mexico