User's Manual

4 5
ATTACHING
These are the simple steps to attaching LucereLight to your bathroom mirror.
(Click on link xxxx to see instructional on youtube.com)
1. ATTACHING TWO LIGHTS (see illustration)
For optimum eective lighting, LucereLight has been designed for use in pairs.
Choose placement of the silicone bases and the lights vertically on the mirror on either side
of your face to give maximum illumination.
First, mount the lights by rmly pressing the silicone bases on to the mirror. Then, simply take
the lights and place them on to the silicone bases. The LucereLight has a built-in magnet that
attracts to a piece of steel inside the silicone base. The curved shape of the mount allows
you to easily adjust the angle of the light for optimum illumination.
NOTE: After each use it is recommended to remove LucereLights from the silicone bases
in order to protect them. If you are traveling or want the lights in a dierent location, you
simply peel o the silicone bases from the mirror and re-attach the silicone bases to any
clean glass surface as described above.
2. ATTACHING ONE LIGHT (see illustration)
If you choose to use only one LucereLight, you may want to place it horizontally on the
mirror above your face, or vertically opposite your face and move from side to side to get
maximum illumination on both sides of your face. (Follow mounting instructions above)
3. FOR LONG TERM ATTACHMENT (see illustration)
For long term attachment use the enclosed removable two-sided tape and attach the plastic
plate(s)directly to your mirror where you desire to have the light(s) on a long-term basis.
Press the silicone base(s) rmly on to the plastic plate(s). Press all around the periphery.
The two holes on the silicone base t on to the two prongs on the plastic plate. The silicone
base is designed to cling to the plastic plate and will stay there permanently until peeled o.
(See above instructions for placement of LucereLights for maximum illumination)
PAIRING SINGLE LIGHTS
If you already own a set of LucereLights, or a single light, and want to add lights to your
collection, then you can purchase as many lights as you want.
Each LucereLight has the ability to pair radio communication with each other.
Follow these simple steps.
1. Ensure both units are NOT in airplane mode (check that the switch on the back
indicates green, not red)
2. On one of the units, simultaneously press and hold the power button and then,
increase brightness icon.
3. After about 5 seconds the indicator LED will start to blink green.
4. On the other unit, press and hold the power button and then decrease brightness icon.
5. After about 5 seconds the indicator LED willstart to blink red.
6. After a few red blinks it should ash green once and stop. The rst blinking green unit
will continue to blink.
7. Press any button on the unit with the blinking green LED to make it stop.
8. The units should now be paired. Any input on one unit should also aect the other one.
It’s now ready for use.
TAKING CARE OF LUCERELIGHT
MAINTENANCE
To ensure maximum adhesion, make sure the mirror or glass is totally clean before at-taching
the silicone bases or plastic plates. We recommend not touching the adhesion surface of
the silicone bases.
In order to avoid dust & particles in the silicone bases, only remove when wanting to travel
with the LucereLight
When traveling with two LucereLights, it is a good idea to attach the two silicone bases to
the plastic plates, back-to-back, to keep clean and protect the adhesion surfaces.
It is important that the silicone bases not be thrown loose into luggage among clothing, to
avoid getting lint on the silicone mounting surface.
If using original packaging as a travel box, place LucereLights and accessories as orig-inally
positioned in the box.
If you wish to move the plastic plates to a dierent location, remove them carefully from
mirror and re-attach with fresh two-sided tape.
If not using original packaging as a travel box, then be sure to wrap lights in a cloth or towel
to avoid scratches or damage.