Lucent Technologies Bell Labs Innovations PARTNER® II Communications System PARTNER® Plus Communications System Release 4.
518-455-338 Issue 2 August 1996 Copyright © 1996 Lucent Technologies All Rights Reserved Printed in U.S.A. Notice Every effort was made to ensure that the information in this Planner was complete and accurate at the time of printing. However, information is subject to change. Trademarks PARTNER and PassageWay are registered trademarks and PARTNER MAIL and PARTNER MAIL VS are trademarks of Lucent Technologies. Ordering Information The order number for this Planner is 518-455-338.
Introduction Setup decisions for the PARTNER® II Communications System or PARTNER Plus Communications System should be recorded on the forms in this Planner. The forms must be filled out before installation to provide guidance for the technician who installs and programs the system. 2. The forms should also be used by the customer to record changes after installation, so there is an ongoing record of the programming for the system.
2 Form A Supplemental Instructions: System Configuration Salesperson completes items 1–12. Sales Support Representative completes items 13–15. VMS-AA Automated Attendant service of PARTNER MAIL™ or PARTNER MAIL VS™, which must be purchased separately. If the receptionist does not answer an incoming call, VMS-AA lets the caller select an extension or route. Programmed using option 1 of Group Call Distribution {#206} for Hunt Group 7.
9. System Settings Receptionist answers calls during business hours? If "Yes," be sure to record settings on these forms that will allow the receptionist to answer the phone before automatic coverage is applied. Number of Lines {#104} This programming procedure should be used only for installation—using it later erases custom settings for all extensions. After installation, use Line Assignment {#301} to assign lines and, for PARTNER II systems only, Pool Extension Assignment {#314} to assign lines to pools.
4 11. Auxiliary Equipment (System) Check boxes that apply for auxiliary equipment connected to the control unit or to system wiring. All appropriate hardware and software must be purchased separately. Battery Backup In some countries, battery backup is available to allow the customer to connect an external battery to keep the complete system operational during a commercial power failure. If it is available and the customer wants battery backup, check this box.
Form B1 Supplemental Instructions: System Extensions This form provides basic information for each system extension. To customize line restrictions or other extension settings, you must also use Form B2. Write Name/Description Write a user name or a description for auxiliary equipment (such as "Fax," "VMS," or "Conference Room") to be installed at the extension.
6 Form B2 Supplemental Instructions: Customized Extension Settings Each row on Form B2 specifies settings—including group assignments—that can be copied to other extensions using Copy Settings {#399}. Default settings are shown at the top of Form B2. Settings for Auxiliary Equipment The following settings may be useful for auxiliary equipment: ■ For a dedicated line (such as a Fax line, see Form A), assign the line to the equipment extension and remove it from other extensions.
Identify Restrictions/Permissions Specify restrictions and permissions for each extension. Line Access Restriction {#302} or Pool Access Restriction {#315} By default, access to all lines and pools is set to No Restriction. To change the default, write the line numbers or pool access codes in the appropriate columns, as follows: Outgoing only – Incoming only – User can place outside calls and receive only transferred calls on specified line or pool.
Form C Supplemental Instructions: Button Templates 8 MLS-34D Telephone There are eight pages to Form C—one page for each type of system phone and one page for an Intercom Autodialer. Use Form C to record line and pool button assignments and to indicate programming for system telephone buttons that do not have lines or pools assigned if the programming is to be performed from extension 10 or 11 during system installation.
Intercom Autodialer The buttons on the Intercom Autodialer are automatically programmed as Intercom Auto Dial buttons for all system extensions in the following order: (PARTNER II system only) 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 You can program the buttons to ring, voice signal, or manually signal; and you can change the order.
10 Example Templates These examples show a PARTNER-34D telephone, PARTNER-CA48 Intercom Autodialer programmed for a PARTNER II system receptionist, and a PARTNER-18 telephone programmed for a PARTNER II system in Hybrid mode for a user at a pooled extension. Buttons that are not used for lines or pools have dial-code features. (The abbreviations are explained in "Button Feature Summary" beginning on page 11.
Button Feature Summary This section lists button features in order by feature type and feature name. For each feature, the first line shows the following information: ■ The name of the feature. ■ Whether a button with lights is required ( ■ An abbreviation that can be entered on the Form C templates. ■ The entries needed to program the feature on a button. Some features can include a two-digit extension number (shown as xx) or a single-digit group number (shown as g).
12 Manual Signaling—Ring MS-x x Feat 1 3 xx Beeps the designated extension. If the user presses Intercom first, pressing the button places a ringing intercom call to the extension, or transfers a call. If on a button with lights, the lights show calling activity at the destination extension. Manual Signaling—Voice Signal Feat 1 3 ★ x x MSVS-xx Beeps the designated extension.
Hunt-g Group Hunting—Ring Intercom 7 7 g Rings the first available extension in the designated Hunt Group, or transfers a call to an extension in the group. If unanswered after 3 rings, the call moves to the next available extension, and so on, until the call is answered or until the caller hangs up.
Form D Supplemental Instructions: Number Lists Use this form to specify lists of Disallowed, Allowed, and Emergency telephone numbers. Also use this form to identify the phone numbers dialed automatically by External Hotlines. NOTE: To restrict long-distance calling, Toll Call Prefix {#402} (indicating whether you must dial a 0 or 1 to place long distance calls) must be set correctly (see Form A, Item 9).
Emergency Phone Number List {#406} External Hotline {#311} You can create a list of emergency numbers that can be dialed at any time by any extension that has access to an outside line. The list can have up to 10 entries. Emergency numbers override all other dialing restrictions, including Night Service with a System Password. For each extension that has been designated as an External Hotline on Form B1, write the telephone number that is dialed automatically when the handset is lifted.
Form E Supplemental Instructions: System Speed Dial Numbers 16 With System Speed Dialing, a user can dial a stored number by pressing four buttons: the Feat button ( # on a standard phone) followed by a 3-digit code. Storing a telephone number as a Speed Dial number lets users dial more quickly. Other kinds of numbers—such as account codes and other dialing sequences—also can be stored as Speed Dial numbers. Telephone Number Write the number exactly as it should be dialed.
Form A: System Configuration Lucent Technologies Required for PARTNER II System and PARTNER Plus System. For additional instructions, see page 2. Bell Labs Innovations 6. Configure Hardware for Hybrid Mode (PARTNER II system only): No ❑ Yes ❑ If yes, call local telephone company— MF Mode and FCC # AS5 USA-21312-MF-E 1. Customer Billing Name 2. Installation Address 5. Sold by 7. Features Customer is most interested in (most important first): Phone 3. Contact Name 4.
Form A: System Configuration Lucent Technologies Bell Labs Innovations 9. System Settings. Write response on line for each item. ● . Receptionist answers calls during business hours? Write "Yes" or "No" ● Number of Lines {#104}—By default, 2 lines per 206 module and 4 lines per 400 module are assigned to each extension (or to pool 880 in PARTNER II Hybrid Mode). Write .
Form A: System Configuration Lucent Technologies Required for PARTNER II System and PARTNER Plus System. For additional instructions, see page 4. Bell Labs Innovation 11. Auxiliary Equipment (System). Check if applicable: ❑ Battery Backup ❑ Caller ID Devices ❑ Loudspeaker Paging: Number of zones ❑ Magic on Hold (Music on Hold {#602} must be active.
Form B1: System Extensions Lucent Technologies Required for PARTNER II System and PARTNER Plus System. For additional instructions, see page 5. Bell Labs Innovations. Ext. Jack No.
Form B1: System Extensions Lucent Technologies Required for PARTNER II System extensions 34 through 57. For additional instructions, see page 5.
Form B1: System Extensions Lucent Technologies PAGE 3 of 4 May be used if Ext. Name Display is checked on Form B1, Page 1 of 4. Bell Labs Innovations Character Codes Ext. Jack No. Write 2-Digit Code for Each Character To Be Displayed — See Table at Right 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Note: Only 12 characters display on MLS-model phones.
Form B1: System Extensions Lucent Technologies PAGE 4 of 4 May be used if Ext. Name Display is checked on Form B1, Page 2 of 4. Bell Labs Innovations Character Codes Ext. Jack No. Write 2-Digit Code for Each Character To Be Displayed — See Table at Right 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Note: Only 12 characters display on MLS-model phones.
Form B2: Customized Extension Settings PAGE 1 of 2 Lucent Technologies Required if you want to change extension settings from defaults for PARTNER II System and PARTNER Plus System. For additional instructions, see pages 6 and 7.
Form B2: Customized Extension Settings Lucent Technologies PAGE 2 of 2 Required if you want to change extension settings from defaults for PARTNER II System extensions 34 through 57. For additional instructions, see pages 6 and 7.
Form C1: PARTNER-34D Phone Lucent Technologies Bell Labs Innovations PAGE 1 of 8 Make as many copies as you need. Use template and/or checklist. For additional instructions, see page 8.
Form C2: Intercom Autodialer Lucent Technologies Bell Labs Innovations Template Instructions ● If desired, write in intercom Ring (Ext-XX) or Voice Signal (ExtVS-XX), or Manual Signal Ring (MS-XX) or Voice Signal (MSVS-XX) ● For additional intructions, see page 9.
Form C3: PARTNER-18 Phone Lucent Technologies Bell Labs Innovations PAGE 3 of 8 Make as many copies as you need. Use template and/or checklist. For additional instructions, see page 8.
Form C4: PARTNER-6 Phone Lucent Technologies Make as many copies as you need. Use template and/or checklist. For additional instructions, see page 8. Bell Labs Innovations Template Instructions ● If desired, write in line number, pool access code, dial code feature, or auto dial number ● If desired, write in Line Ringing (Imm, Del, or No) from Form B2 ● If desired, write in Line Access Restriction or Pool Access Restriction (Out, In, or No) from Form B2 Intercom PAGE 4 of 8 Intercom Ext.
Form C5: MLS-34D Phone Lucent Technologies PAGE 5 of 8 Make as many copies as you need. Use template and/or checklist. For additional instructions, see page 8.
Form C6: MLS-18 Phone Lucent Technologies PAGE 6 of 8 Make as many copies as you need. Use template and/or checklist. For additional instructions, see page 8.
Form C7: MLS-12 Phone Lucent Technologies Bell Labs Innovations PAGE 7 of 8 Make as many copies as you need. Use template and/or checklist. For additional instructions, see page 8.
Form C8: MLS-6 Phone Lucent Technologies Make as many copies as you need. Use template and/or checklist. For additional instructions, see page 8. Bell Labs Innovations Template Instructions ● If desired, write in line number, pool access code, dial code feature, or auto dial number ● If desired, write in Line Ringing (Imm, Del, or No) from Form B2 ● If desired, write in Line Access Restriction or Pool Access Restriction (Out, In, or No) from Form B2 Intercom PAGE 8 of 8 Intercom Ext.
Form D: Number Lists Lucent Technologies Required if Form B1 identifies External Hotlines, or if Form B2 identifies Disallowed or Allowed List Assignments. For additional instructions, see pages 14 and 15. Bell Labs Innovations Disallowed Phone Number Lists {#404} Emergency Phone Number List {#406} Required only if Disallowed List Assignment {#405} is specified on Form B2.
Form D: Number Lists Lucent Technologies PAGE 2 of 2 Required only if Forced Account Code Verification is desired. For additional instructions, see page 15. Bell Labs Innovations Forced Account Code List {#409} Entry 1 Account Code (up to 6 digits) Write Description 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1. Valid entries are 0-9; write ! for wildcard (press Hold to program).
Form E: System Speed Dial Numbers Lucent Technologies PAGE 1 of 1 Optional for PARTNER II System and PARTNER Plus System. For additional instructions, see page 16. Bell Labs Innovations To Dial: On system phones, press Feat + 3-digit code. On standard phones, press # + 3-digit code while receiving intercom dial tone.
Lucent Technologies 518-455-338 Issue 2 August 1996
