Model No. AF4001 Owner’s Manual AIR FILTRATION SYSTEM QUESTION... 1•847•780•6120 Visit us on the web at powertecproducts.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
TABLE OF CONTENTS SECTION SAFETY RULES PAGE 1 PRODUCT SPECIFICATIONS Horsepower (Maximum Developed) . . . . . . . . . . . . . 1/6 HP Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 V Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz ASSEMBLY 2 Controls . . . . . . . . . . . . . . . . . . . Manual or Remote Control Number of Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING For your own safety, read and understand all warnings and operating instructions before using any tool or equipment. WARNING Some dust created by operation of power tool contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. To reduce your exposure to these chemicals, work in a well ventilated area and work with approved safety equipment. Always wear OSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.
SPECIFIC SAFETY RULES 2 2 SPECIFIC SAFETY RULES FOR AIR FILTRATION SYSTEM Be aware of general power tool safety. Make sure all the safety rules are understood. • To reduce the risk of electrical shock, do not expose air filtration to water or rain. • Disconnect the machine from power source whenever adjusting or replacing any parts. • Never duct a machine directly into the air filtration system. • Do not plug air filtration system in unless switch is in the “OFF” position.
ASSEMBLY INSTALLATION Figure 2 Refer to Figure 1 to 4 This air filtration system is specifically designed to circulate and filter non-metallic dust, which is generated throughout the work area. The unit can be located on a work bench or hung from an overhead support. When selecting a location ensure the power source is easy to access. Use the carry handle when moving the unit.
ASSEMBLY Do not permit fingers to touch the terminals of plug when installing or removing from outlet. POWER SOURCE WARNING Do not connect to the power source until the machine is completely assembled. 4 The machine is wired for 120 volts, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position. Running the unit on voltages which are not within range may cause overheating and motor burn-out.
Refer to Figure 7 to 8 This air filtration system can be controlled using the remote control (Figure 7) or the control panel (Figure 8) located at the rear of the unit. NOTE: The filtration timing can ONLY be controlled with the remote. ON/SPEED CONTROL TO TURN THE UNIT OFF Press the OFF button on the remote control or the control panel to turn the unit off. Figure 7 5 FILTRATION TIMING NOTE: The filtration timing can ONLY be controlled with the remote.
MAINTENANCE MAINTENANCE 6 FUSE REPLACEMENT WARNING Disconnect the machine from power source whenever adjusting or replacing any parts. CHANGING THE FILTERS Refer to Figure 9 6 The inner and outer filters should be replaced and / or cleaned depending on the amount of usage and the environment of your workshop. Clogged filters will reduce the amount of air circulation. • Lift up on the clips located at the top and bottom of the cabinet and remove the outer filter.
SYMPTOM POSSIBLE CAUSE(S) Motor does not run 1. 5 7 CORRECTIVE ACTION Machine not plugged in 1. Plug power cord into electrical receptacle 2. ON/SPEED button is in "OFF" position 2. Press the ON/SPEED button to turn unit on 3. 4. 5. Power switch or cord is faulty Blown fuse or tripped circuit breaker Remote control is not working 3. 4. 5.
8 PARTS LIST 8 54 63 53 65 64 27 55 72 26 56 57 (13) 25 52 62 58 61 A2 wire 15 14 60 (51) (2) 73 16 17 (13) 18 19 20 21 59 AS02 7 9 10 11 8 13 22 23 12 (1) (2) (3) 24 (1 9) (2 0) (2 1) 6 A1 wire 5 28 Label 6 8 Label 6 6 29 Label 6 7 30 4 35 69 As01 74 43 3 2 1 46 48 49 50 47 32 45 33 42 44 34 (2 3) 41 71 A1 wire 40 36 39 38 37 A2 wire ( 21) 51 ( 24) AIR FILTRATION SYSTEM PARTS ILLUSTRATION Figure 10 (13) (2)
Key No. Part No. Description Specification Qty Key No.
WARRANTY 10 WARRANTY Thank you for investing in a POWERTEC product. This product has been designed and manufactured to meet high quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12 months from the date of purchase. This guarantee does not affect your statutory rights. LIMITED 1 YEAR WARRANTY AND 30-DAY SATISFACTION GUARANTEE POLICY 10 POWERTEC products are designed and manufactured by Southern Technologies LLC.
NOTE
Southern Technologies, LLC Waukegan, IL 60087
