CONTENTS Chapter 1:DVR Features .......................................................................................................................................................2 Chapter 2:Layoutt..................................................................................................................................................................3 2.1 Front Panel ..................................................................................................................................
6.2 Log-in Net-viewer.........................................................................................................................................................23 6.3 Main Interface of Net-viewer .......................................................................................................................................23 6.3.1 Menu column ..................................................................................................................................................
Safety Instruction 1. Use proper power source. Do not operate this product from a power source that applies more than specified voltage (100-240V AC). 2. Never insert anything metallic into the DVR case. Putting something into the DVR case can be a source of dangerous electronic shock. 3. Do not operate in wet & dusty or use near water. Avoid places like a damp basement or dusty hallway. 4. Do not expose this product to rain or use near water.
Chapter 1:DVR Features Real time monitoring With Monitor and VGA virtual output, Support Net-viewer and MP real time surveillance function Recording function H. 264 compression, recording frame adjustable and support multiple recording modes, including: Continuous, Scheduled, Manual, Alarm and motion detection recording etc.
Chapter 2:Layoutt 2.1 Front Panel 2.1.
8 9 10 CH+: Switch to next CH ALL: Preview all CH REW: Slow play / Left 18 19 20 SEL/EDIT: Select / Edit DOWN: Down direction PTZ: Enter POP-UP menu / PTZ 2.2 Rear Panel 2.2.1 1 2 3 4 5 4-CH Rear Panel (Details please refer to the real product) CH1-4: Video input Video Output Audio Input Audio Output LAN: LAN port 2.2.
2.3 Remote Controller （Only for reference) 1-8 Channel Select 1-8 ; Numeric key 9、0 Numeric Key ALL Preview all Channel Menu Enter/Exit Main Menu ▲ Up Key ▼ Down Key ◄/ Left / Right Key SEL Select Key/ Edit Key Rewind key Play Key, Enter to recording search menu Forward Key ● Manual Recording Pause / Frame Play ■ Stop manual recording; Stop Playback Audio Undefined Mute Undefined Mouse Operation You could proceed mouse operation, except of front panel and remote controller.
Chapter 3:DVR Installation 3.1 Hard Disk Installation Caution： Please do not take out hard-disk when DVR is running! Removable HDD installation 1. Please use attached key to open the removable box 2. Take out the removable HDD and connect HDD port to according data cable/power cord; 3. Put the removable HDD back body. Fixed HDD installation 1. Open DVR upper cover carefully; 2. Insert Power Cord and data cable into Pin of hard-disk tightly; 3. Put the upper cover back carefully. 3.
Chapter 4: DVR Boot up 4.1 System Initialization After connecting the power adapter and turning on the power button, the system will boot-up and start initializing. Note： 1. All the pictures shown as user manual are provided only for your ref. 2. DVR is an abbreviation of the “Digital Video Recorder Equipment”. Picture 4-1 4.2 Main Interface After finishing system initialization you are allowed to enter into main interface.
5.1 Main Menu Preview Camera Color set Recording Search Network Playback Rec. Search Detail File File Backup Main Menu HDD Management E-mail setting Alarm Setting Device Management PTZ Setting Mobile Motion Area setting Time Setting User password Video Setting System Language Select System Information System Maintenance 5.2 Main Menu Picture 5-2 After clicking right key of mouse, pop-up menu will be prompted to screen.
5.2.1 Camera Enter into [Main Menu Æ Camera] to set up name and position of each channel (Shown as Picture 5-3), Furthermore, you could also adjust image brightness, saturation, contrast and hue parameters of each channel after entering into [Color] Menu and set up if each channel could be previewed or not under Live display and/or Recording mode. Please note that the name of each channel supports up to eight characters or four Chinese characters.
When Audio is set to “On”, system will also record audio signal and will have audio output on playback mode; on the contrary, “off” means you could not record audio signal and will have no audio output on playback mode. If recording mode is set to scheduled recording, click the “Schedule”, the menu interface shows as follows (picture 5-6): Recording channels include All, CH-1, CH-2, CH-3, CH-4 respectively. Please click the channel you needed.(p.s.
When selecting static allocation, you need to setup IP address, net-mask, gateway and web port (shown as picture 5-9). Picture 5-9 Picture 5-9 If you apply for DDNS service and set up net parameter of DVR accordingly, you could visit DVR remotely via IE browser. (shown as picture 5-10) Picture 5-10 If you need to visit DVR via Internet, you should setup the inflection of video port at the public Router located in the DVR (shown as Picture 5-11). Host Port: 9000 Web Port: 8080 LAN IP address of DVR: 192.
File list Picture 5-13 On the [Video search] menu mode, please click [File list] to pop up below sub-menu (Picture 5-13). When selecting recording date and time you want to search and clicking [Search] button, now you could playback the recordings during the period. Based on the [time search] menu, you also could further search one recording by selecting Channel and/or Recording type. First：Indicates the first page of recording history which you have searched.
3. Open backup file: (1) Click [Play] menu (P) on the top of multimedia player interface to select playing the backup file; (1) Click pop-up menu button on the bottom of multimedia player and [Play- ] button, then the backup file will be played on the according channel. (2) The Menu brief on the bottom of multimedia player: Date: recording date for the current backup file shown as right corner; 24H recording time quantum: lie under [Date] menu.
4. Please refer to the below [Video on] setting procedure (System default video for every channel is on). SettingÆVideo play setting ÆNormal video BarÆSelect the channel you need to displayÆ Select videoÆApplyÆOK play the 5. And refer to the below [Audio on] setting procedure. (Setting parameter will be available only when opening multimedia player again after successful [Audio on] setting.
Total space: indicates HDD total saving size. Free space: indicates current HDD available saving space. Useable REC time: As per current image detail/quality and frame rate, system will show to you how much time you could continue to record. Overwrite: When selecting “on”, that means system will auto-overwrite previous recording once HDD if full; when selecting “off”, recording will stop once HDD is full HDD Format: If HDD is used firstly, please do format the HDD in order to make DVR data safe.
Email Setting Click the [Email setup] menu to enter into its sub menu (shown as Picture 5-20). Picture 5-20 On the [Email setup] mode, please refer to its parameters set shown as picture 5-21 when setting email alarm to “on”. SSL: is a kind of security link transport protocol. You could encrypt your communication info (including your email) via using the SSL to prevent hacker monitoring your email or communication info and even your password. Picture 5-21 Please set SSL to “On” via Gmail.
Picture 5-23 5.2.6.3 PTZ Setup Picture 5-24 Enter into [Main menuÆ Device ÆPTZ Setup] to select the PTZ channel you want to control and set PTZ protocol (Pelco-D, Pelco-P), Baud rate (1200、2400、4800、9600), Data bit (8、7、6、5), Stop bit (1、2), Parity Check（None、Odd、Even Mark Space）and address code respectively. Please note you could operate PTZ control only when the above-mentioned channel parameter must be consistent with parameter set of PTZ control.
Firstly you need to install widget provided by attached CD disk and copy the file with suffix “QQeye.CAB” to mobile phone (also you could transmit the widget and file with “QQeye.CAB” to mobile phone via blue-tooth technology). 3、Choose defaulted device and 2. Click the widget you need to click[Install] button to start the install and choose a location to installation (please refer to install “digitalsal QQeye” after below installation processing finishing initialization detection. display.
When operation system of mobile phone is based on Symbian,procedure as follows: Firstly you need to copy the file with suffix “QQeye.CAB” provided by attached CD disk to mobile phone (also you could transmit the widget and file with “QQeye.CAB” to mobile phone via blue-tooth technology). Copying file is defaulted to save to storage card, and the file transmitted by blue-tooth technology to save to receiver box 1、Installation initializing 2、System will pop up sub window (Shown as follow picture).
9、Parameter setting Default Access Point：Indicate select access point. System default the access point is GPRS connection. Server Address：Indicate IP address and DDNS of DVR on the public network. Server Port：Web port: Same as other web port setting, you need to map the web port to Router. Setting range is between 1024 and 65535. Please note the port number not equal to other web port setting under the IP address User Name:same as user name set to DVR. Password：same as password set to DVR.
5.2.7.1 Time Set Click the [Main menuÆSystemÆDate/Time] in turn to enter into [Time Set] menu. You could not only modify system date, time and format, but also set daylight saving time and mode. Picture 5-29 5.2.7.2 Password The option allows you set the device ID and set system password. The modification to these parameter values will be available after clicking [APPLY] button.
5.2.7.5 Info. Click [Main MenuÆ SystemÆInfo] to enter into [System Information] menu for viewing system info., including Device type, Software version and MAC address etc. Picture 5-34 5.2.7.6 System Maintenance Picture 5-35 The option allows you recover ex-factory default, update system software and set system auto-maintenance. Click [Main menuÆSystemÆMaintain] to enter into the [System Maintain] menu (shown as Picture 5-35).
Chapter 6： NetViewer Program 6.1 Plug-ins download and installation Open IE browser and input IP address and web port of DVR, such as http://172.18.6.202:8080/ and confirm to download and install widget. If your computer is connected to Internet, computer will auto download and install the widget. .Remind: If the widgets are not downloaded successfully, please check if your browser’s safety level or firewall setting is too advanced. 6.
6.3.1 Menu column Menu column include [Live] menu, [Replay] menu and [Setup] menu. 6.3.1.1 Live After Logging-in system, system will enter into live display (shown as Picture 6-3). 6.3.1.2 Replay The option allows you click the [Replay] button to playback recording remotely. Firstly please select the day, channel and type and proceed searching and refreshing; secondly select any event from search result list to playback.
Click the [Schedule] menu to enter into its sub menu (shown as Picture 6-6). Picture 6-6 2 Alarm ○ Click [Alarm] menu to enter into its sub menu (shown as Picture 6-7). You could set I/O alarm for every channel, motion detection alarm, motion recording, motion trace, motion sensitivity, video loss alarm, HDD space alarm, HDD invalidation alarm and alarm output time etc Details setting method please refer to section 5.2.5.
4 Network ○ Click [Network] to enter into [Network] menu. Relative parameters are the same as local DVR Details please refer Section 5.2.3. – Network Se 5 Setting ○ Picture 6-10 Click [setting] menu to enter into its sub menu interface (shown as Picture 6-11); Click […] button to preview net-viewer recording saving path and screen capture saving path.
Chapter 7：Specification Model 4-CH 8-CH Video System NTSC / PAL(Optional) Compression Format Video：H.
Chapter 8: Appendix 8.1 Recording Alarm setting Please refer the below matrix: “⊥” stand for “only alarm but no recording”; “AMR” stand for “alarm recording”; “NLR” stand for “normal recording”; and “NOR” stand for “ no recording”. Once alarm is triggered, alarm icon will occur, and when many alarms are triggered, alarm remarks will occur on the screen.
21cn VIP mail vip.21cn.com vip.21cn.com etang.com smtp.etang.com pop.etang.com elong.com: smtp.elong.com pop3.elong.com List 8-3 8.3 Usage Maintenance 1. 2. 3. 4. 5. Please make sure DVR keep away from heating source. Clean the internal dust regularly, keep DVR aeration well and be easy to heat dissipate. Please not plug in RS-232 and RS-485 when power is on to avoid any damage to the port. Please check the HDD cable and data cable to avoid the cable aging.
The material in this document is the intellectual property of our department . No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without our department prior written permission. Our products are under continual improvement and we reserve the right to make changes without noti ce. But no guarantee is given as to the correctness of its contents. We do not undertake any responsibility for the harms cause by using our product.
