Technical Specifications

SHOP-FABRICATED STRUCTURAL WOOD 06 17 00
LP - Building Products
SPEC-DATA
®
and MANU-SPEC
®
are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Data. All Rights Reserved.
®
below per project requirements and specifier’s practice.
A. Manufacturer: LP - Building Products.
1. Contact: 414 Union St., Nashville, TN 37219; Telephone: [phone]; Fax: [phone];
E-mail:
[e-mail]; website: www.lpcorp.com.
Specifier Note: If a Division 01 Section covers substitutions on a project-wide basis, do not repeat the requirement here. Do not include
substitution procedures here unless they are not defined elsewhere.
2. Single Source Responsibility: Provide components and materials specified in this section from a single manufacturer.
3. Substitution Limitations:
a. Substitutions: [In accordance with Section 01 25 13 - Product Substitution Procedures] [______]] [No
substitutions permitted].
Specifier Note: Include an overall description of the system, assembly, product or material. Include required properties or characteristics
that do not obviously belong under other titles. Examples: configuration, size and color.
B. Description: Laminated Strand Lumber, including the following:
Specifier Note: LSL is limited to a maximum of 4 plies for thicknesses of 1 3/4 inches (44.5 mm) and less and to 2 plies for all other
thicknesses.
1. LP LSL 1730F
b
-1.35E:
a. Material: Strands arranged parallel to the finished product’s length.
b. Adhesive: MDI, bonded and cured under pressure and heat.
c. Thickness: [1 1/4 inches (31.8 mm)] [1 1/2 inches (38.1 mm)] [1 3/4 inches (44.5 mm)] [3 1/2 inches (90 mm)].
d. Plies: [1] [2] [3] [4].
e. Depth: [3 1/2 inches (90 mm)] [4 1/4 inches (108 mm)] [4 3/8 inches (111 mm)] [5 1/2 inches (140 mm)] [7 1/4
inches 9184 mm)] [9 1/4 inches (235 mm)] [9 1/2 inches (241 mm)] [11 1/4 inches (286 mm)] [11 7/8 inches (302
mm)] [14 inches (356 mm)] [16 inches (406 mm)] [18 inches (457 mm)] [20 inches (508 mm)] [22 inches (559
mm)] [24 inches (610 mm)].
f. Water Resistant Coating: [Provide proprietary edge and end seal coating] [No coating required].
2. LP LSL 2360F
b
-1.55E:
a. Material: Strands arranged parallel to the finished product’s length.
b. Adhesive: MDI, bonded and cured under pressure and heat.
c. Thickness: [1 1/4 inches (31.8 mm)] [1 1/2 inches (38.1 mm)] [1 3/4 inches (44.5 mm)] [3 1/2 inches (90 mm)].
d. Plies: [1] [2] [3] [4].
e. Depth: [3 1/2 inches (90 mm)] [4 1/4 inches (108 mm)] [9 1/4 inches (235 mm)] [9 1/2 inches (241 mm)] [11 1/4
inches (286 mm)] [11 7/8 inches (302 mm)] [14 inches (356 mm)] [16 inches (406 mm)].
f. Water Resistant Coating: [Provide proprietary edge and end seal coating] [No coating required].
3. LP LSL 2640F
b
-1.75E:
a. Material: Strands arranged parallel to the finished product’s length.
b. Adhesive: MDI, bonded and cured under pressure and heat.
c. Thickness: [1 1/4 inches (31.8 mm)] [1 1/2 inches (38.1 mm)] [1 3/4 inches (44.5 mm)] [3 1/2 inches (90 mm)].
d. Plies: [1] [2] [3] [4].
e. Depth: [3 1/2 inches (90 mm)] [4 1/4 inches (108 mm)] [9 1/4 inches (235 mm)] [9 1/2 inches (241 mm)] [11 1/4
inches (286 mm)] [11 7/8 inches (302 mm)] [14 inches (356 mm)] [16 inches (406 mm)] [18 inches (457 mm)].
f. Water Resistant Coating: [Provide proprietary edge and end seal coating] [No coating required].