Installation Instructions

ManualsBrandsLowrance ManualsMarineStructureScan Sonar Imaging

StructureScan Installation

Contents

Your StructureScan box is packed with the LSS-1 black box, a Power cable,

StructureScan transducer, mounting bracket, 15 foot (4.5m) ethernet cable and a

hardware kit. The transducer has a 20 foot (6m) cable attached.

Hardware Mounting Kit (Included)

Transom mount screws (2)

Transducer attachment lock

nuts (6)

Bracket Assembly bolts (2) LSS-1 Mounting screws (4)

Bracket Assembly washers (4) Closed end crimp connector (1)

Bracket Assembly nuts (2) Zip ties (2)

Transducer attachment bolts (6)

Required Tools and Supplies (Not Included)

Drill Phillips (slotted-head) screwdriver

Drill bits

Marine grade above- or below-

waterline sealant

LSS-1 module, ethernet cable, StructureScan transducer, transducer

mounting bracket and power cable.

Summary of content (12 pages)

PAGE 1
StructureScan Installation Contents Your StructureScan box is packed with the LSS-1 black box, a Power cable, StructureScan transducer, mounting bracket, 15 foot (4.5m) ethernet cable and a hardware kit. The transducer has a 20 foot (6m) cable attached. LSS-1 module, ethernet cable, StructureScan transducer, transducer mounting bracket and power cable.
PAGE 2
7.5”(191.mm) 7.4”(188mm) 2.1”(55.5mm) 7.5”(190.7mm) 2.8” (72.7mm) 8.26” (210mm) 6.8”(173.4mm) 2.27” (57.6mm) Installation When mounting the StructureScan transducer, make sure the there is nothing around the mounting location that could interfere with the StructureScan transducer sonar beams. Sidescan Downscan Sonar Mounting Options The StructureScan transducer can be mounted on the transom, jackplate, step, trolling motor or directly to your boat’s hull.
PAGE 3
StructureScan Transducer Mounts Transom Mount (Page 6) Jackplate Mount (Page 7) Step Mount (Page 8) Direct Mount/Step (Page 9) Trolling Motor Mount (Sold separately) (Page 10) • eeps transducer in the water when the boat is K on plane, allowing you to track bottom at high speeds • ransducer angle can be adjusted so it is parallel T with the water • ransducer more likely to collide with obstructions T in the water and adds drag to the boat • Transducer is not in the water when boat is o
PAGE 4
Bracket and Transducer assembly The StructureScan bracket comes with four washers, two bolts and two nuts. If you plan to mount the StructureScan transducer directly to the step (Step Mount) or on the trolling motor, you do not need to assemble the bracket.
PAGE 5
Mounting the LSS-1 The LSS-1 can be mounted under the dash, in the rod locker or in the battery compartment. Select a mounting location that will protect the LSS-1 from standing water. To mount the LSS-1: 1. M ake sure the transducer cable is long enough to connect to the LSS-1 from the desired transducer mounting location. If the 20’ transducer cable is not long enough, a 10’ extension cable is available (part number: 99-006). 2.
PAGE 6
Transom Mount The StructureScan transducer can be mounted just like a skimmer transducer, where it is in the water when you are on plane or can be mounted so it is only in the water, when you are moving at trolling speed.
PAGE 7
Jackplate Mount You can mount the StructureScan transducer inside or outside of the jackplate by drilling through the jackplate, then inserting bolts though hinge hole in the side of the bracket mount into the jackplate. Jackplate Mount Supplies (not included) M6 or 1/4” Drill bit (Jackplate Mount) pilot holes 1/4” (M6) jackplate mount bolts To Mount StructureScan on Jackplate: 1. C hoose a transducer location on the inside or outside of the jackplate. 2.
PAGE 8
Step Mount Mounting the StructureScan transducer under the step not only protects the transducer from hitting objects in the water, but does not cause any drag on your boat when it is on plane. Step Mount Supplies (not included) 1/8” Drill bit (Transom mount pilot holes) Marine grade above- or belowwaterline sealant To use Step Mount: 1. Choose a transducer location. 2. R oute the transducer cable to the location where the LSS-1 will be installed. 3.
PAGE 9
Direct/Step Mount (No Bracket) When using the direct mount installation shown below, you MUST turn on the Flip Left/Right feature. Refer to your Operation manual for more information. Direct Step Mount Supplies (not included) 3/32 Drill bit (Direct/Step mount pilot holes) Marine grade above- or belowwaterline sealant To use Direct Mount: 1. Make sure the boat’s step is the same length or longer than the StructureScan transducer. 2.
PAGE 10
Trolling Motor/Towfish Mount The StructureScan transducer can be mounted on a trolling motor or towfish with the purchase of a trolling motor mount accessory kit. Trolling Motor Mount (sold separately — p/n: 000-00099-004) Trolling motor bracket Hose Clamps (2) No 8. Transducer attachment bolts (6) Zip ties (4) Transducer attachment lock washers (6) To mount transducer on trolling motor or towfish: 1. Make sure the transducer cable can be routed to the LSS-1. 2.
PAGE 11
Powering the LSS-1 The LSS-1 power cable has four wires; red (+), black (–), yellow and blue. The red wire is positive, the black wire is the ground and the yellow wire connects to a switch. The blue wire will not be used. Cut it flush and cover the end with a wire nut or electrical tape.
PAGE 12
Visit our website: www.lowrance.