Operation Manual

The miniature battery SEIKO CR2016, Maxell CR2016
or SONY CR2016 which powers your watch should
last approximately 4 years. However, because it is
inserted at the factory, the actual life of the battery
once in your possession may be less than 4 years.
Be sure to replace the battery to prevent any
possible malfunction as soon as it runs down. To
replace the battery we recommend taking the
watch to a local watch repair shop.
Note: If the alarm is used for more than 20 seconds
a day and/or the illuminating light for more
than 8 seconds a day, the battery life may
be less than the specified period.
■
BATTERY CHANGE
■
HOW TO SET THE SECOND TIME ZONE
■
ILLUMINATING LIGHT
In any mode press S4 to illuminate the display for
about 3 seconds.
Note:
1. The backlight of the watch employs an electro-
luminescent (EL) light, which tends to lose
illuminating power after very long use.
2. The illumination provided by backlight may be
hard to see when viewed under direct sunlight.
■
CARE OF YOUR LORUS WATCH
This watch contains precise electronic components.
Never attempt to open the case or remove the
back cover.
• BATTERY
CAUTION
Do not expose the old battery to fire or
recharge it. Keep it at a place beyond
the reach of chil dren. If a child swallows
it, consult a doctor immediately.
• WATERRESISTANT
Condition
of use
Accidental
contact
with water,
such as
splashes
and rain
Swimming
and taking
a shower
Skin
diving
Scuba
diving
Indication
on the dial/
case back
No
Indication
* If your watch is 200 M/20 BAR, 100 M/10 BAR
or 50 M/5 BAR water resistant, it is so indicated
on the dial/case back.
• Donotoperatethebuttonswhenthewatchis
wet.
• Ifthewatchisexposedtosaltwater,rinseitin
fresh water and then wipe it thoroughly dry.
• Shouldyoufindanywaterorcondensation
inside the watch, immediately have it checked.
Water can corrode electric parts inside the
case.
NO NO NO
YES YES NO NO
YES YES NO
NO
NO
NO
YES
WATER
RESISTANT
WATER
RESISTANT
(50M/5BAR )
WATER
RESISTANT
100M/10BAR
or above
(
NO
(
Caution:
Leather straps are not water resistant except
so indicated, even if the watch head is water
resistant.
• ALLERGICREACTION
Because the case and band touch the skin
directly, it is important to clean them regularly. If
not, shirt sleeves may be stained and those with
delicate skin may develop a rash. Please wear
the watch with some play to avoid any possible
allergic reaction. If you develop a rash on your
wrist, stop wearing and consult a physician.
• MAGNETISM
Your watch will be adversely affected by strong
magnetism.Keep it away from close contact with
magnetic objects.
• SHOCKSANDVIBRATIONS
Your watch may be worn for normal sports
activities, but be careful not to drop it or hit it on
hard surfaces.
• TEMPERATURE
Your watch is preadjusted so that constant
accuracy may be insured at normal tem pera ture.
• CLEANING
Use only a soft cloth and clean water for cleaning
your watch. Never use chemicals, as the
waterproof gasket will corrode.
■
SERVICE
When your LORUS watch requires repair or
servicing, please see the enclosed WARRANTY/
GUARANTEE.
Printed in China
TIMER OPERATION
1. Press S1 in the TIMER mode to start the timer.
2. Press
S1 to stop the timer.
3. To reset the timer to its starting value, press
S2 .
4. Press
S3 to return to the NORMAL TIME mode.
From 3 minutes before the time is up, the warning
beeps (BI-BI) will be generated each time the
second digits reach “00” and “30.” For the last 10
seconds before the time-up time, the alarm (BI)
will sound. When the time is up, the alarm (BI-BI-BI)
sounds for 10 seconds. Press
S1 , S2 or S3 to stop it.
S1
Start
Stop
Reset
S1
S2
(to its starting value)
YES
From the NORMAL TIME mode, press S3 four times
to go to the SECOND TIME ZONE mode. The SECOND
TIME ZONE mode indicator appears on the display.
1. Press
S2 to change the display to the TIME ZONE
SETTING mode. The hour digits start flashing.
2. Press
S1 to set the hour digits. One digit (flashing)
is increased with each press of
S1 . To move the
digits quickly, keep
S1 pressed.
3. Press
S3 to confirm the hour setting and move
on to the minute setting. The minute digits start
flashing.
4. Press
S1 to set the minute digits. The minute digits
are increased in 30-minute increments.
5. Press
S2 to complete the second time zone
setting.
6. Press
S3 to return to the NORMAL TIME mode.
■
HOW TO USE THE TIMER
From the NORMAL TIME mode, press S3 three times
to go to the TIMER mode. The TIMER mode indicator
“TR” appears on the display.
1. Press
S2 to change the display to the TIMER
SETTING mode. The hour digits start flashing.
2. Press
S1 to set the hour digits. One digit (flashing)
is increased with each pressing of
S1 . To move
the digits quickly, keep
S1 pressed.
3. Press
S3 to confirm the hour setting and move
on to the minute setting. The minute digits start
flashing.
4. Press
S1 to set the minute digits. One digit
(flashing) is increased with each pressing of
S1 .
To move the digits quickly, keep
S1 pressed.
5. Press
S3 to confirm the minute setting and move
on to the second setting. The second digits start
flashing.
6. Press
S1 to set the second digits. One digit
(flashing) is increased with each pressing of
S1 .
To move the digits quickly, keep
S1 pressed.
7. Press
S2 to complete the timer setting.
TIMER mode indicator
SECOND TIME ZONE
mode indicator
NREZ017.indd 2 12/01/31 10:07