Operation Manual

■
CHARACTERISTICS
1. Time/Calendar Display: Hour, minute, second,
month, date and day of the week.
2. Time Indication: Choice of 12-hour display
format with PM indicator or 24-hour display
format is available.
3. Stopwatch: The stopwatch can measure up
to 23 hours 59 minutes and 59 seconds in 1/100-
second increments. Lap time measurement is
available.
4. Timer: The countdown timer can be set up to 23
hours 59 minutes and 59 seconds.
5. Daily Alarm: The alarm can be set to sound at
the designated time on a 24-hour basis.
6. Second Time Zone: Time in a different time zone
can be displayed.
7. Chime: The chime can be set to sound every
hour on the hour with a single beep.
8. Illuminating Light: The built-in electro-
luminescent (EL) light evenly illuminates the
display for easy viewing in darkness.
■
BUTTONS AND DISPLAYS
■
HOW TO SET THE TIME/CALENDAR
■
HOW TO USE THE STOPWATCH
1. From the NORMAL TIME mode, press S2 once
to change the display to the TIME/CALENDAR
SETTING mode. (The second digits start flashing.)
2. <Second setting>
Press
S1 in accordance with a time signal.
The second digits are reset to“00” and start
counting immediately.
When the second digits count any number
from “30” to “59” and
S1 is pressed, one
minute is added and the seconds are
immediately reset to “00.”
3. Press
S3 to confirm the second setting and move
on to the next item.
Selection of the item to be adjusted (flashing) is
made in the following order when
S3 is pressed.
*Choice of 12-Hour/24-Hour format
The time display format in either 12-hour
indication or in 24-hour indication can be
selected alternately by pressing
S1 . Under the
12-hour indication format, “PM” mark appears in
the afternoon, but no AM mark appears in the
morning. Under the 24-hour indication format,
no mark appears on the display.
* Measurement and release of lap times can be
repeated when
S2 is pressed.
* When
S2 is pressed, the display changes to show
the current lap time and total time from START for 3
seconds, and then it automatically returns to show
the ongoing measurement.
From the NORMAL TIME mode, press S3 to go to the
STOPWATCH mode. The STOPWATCH mode indicator
“SP” appears on the display.
STOPWATCH OPERATION
Standard Measurement
Lap Time Measurement
Start
Lap 1
Last lap
Stop
S1
S2
S2
S2
S1
Lap 2
Reset
S2
S1
Start
Stop
Reset
S1
S2
(to its starting value)
NREZ017
3-2012
CAL. Z017 (R23 SERIES)
Press S2 to reset the stopwatch.
Press
S3 to return to the NORMAL TIME mode.
4. To set the digits for each item, press
S1 . One digit
(flashing) is increased with each pressing of
S1 .
To move the digits quickly, keep
S1 pressed.
5. After all the adjustments are completed, press
S2 to return to the NORMAL TIME mode.
How to stop the alarm while sounding
The alarm sounds for 20 seconds at the designated
time. To stop it manually while sounding, press
S1 ,
S2 or S3.
Note: The alarm can be set only in one time
zone.
STOPWATCH
STOPWATCH mode indicator
STOP
LAP TIME DISPLAY
**Calendar display
To view the calendar (month and date), keep
pressing down
S1 in the NORMAL TIME mode.
*
“PM” mark
PM
SECOND
DAY OF THE WEEK
12/24-HOUR FORMAT
DATE
HOUR
MINUTE
S3
S3
S3
S3
S3
S3
MONTH
S3
■
HOW TO USE THE ALARM
From the NORMAL TIME mode, press S3 twice to go
to the ALARM mode. The ALARM mode indicator
“AL” appears on the display.
1. Press
S2 to change the display to the ALARM
SETTING mode. The hour digits start flashing.
2. Press
S1 to set the hour digits. One digit (flashing)
is increased with each press of
S1 . To move the
digits quickly, keep
S1 pressed.
3. Press
S3 to confirm the hour setting and move
on to the minute setting. The minute digits start
flashing.
4. Press
S1 to set the minute digits. One digit
(flashing) is increased with each press of
S1 . To
move the digits quickly, keep
S1 pressed.
5. Press
S3 to confirm the minute setting and move
on to the time zone setting.
6. Press
S1 to select the time zone. Select “t1” for
alarm in the time zone 1, select “t2” for alarm in
the time zone 2. The alarm is available only in
one time zone.
7. Press
S2 to complete the alarm setting.
8. Press
S3 to return to the NORMAL TIME mode.
■
ENGAGEMENT/DISENGAGEMENT OF
THE ALARM & CHIME
1. From the NORMAL TIME mode, press S3 twice to
go to the ALARM mode.
2. With each press of
S1 , the alarm and chime
can be engaged or disengaged in the following
order. The ALARM signal and/or CHIME signal
appear on the display accordingly.
3. Press
S3 to return to the NORMAL TIME mode.
ALARM mode indicator
CHIME signal
ALARM signal
**
To change the display mode, press S3. The display
mode changes in the following order.
STOPWATCH
NREZ017.indd 1 12/01/31 10:07