User's Manual
Table Of Contents
- 1 Important Safeguards
- 2 Package Contents
- 3 Recorder Overview
- 4 Basic System Setup
- 5 Camera Installation
- 6 Using the Mouse
- 7 Setting the Date & Time
- 8 Using the On-Screen Display
- 9 Recording
- 10 Playback
- 11 Backup
- 12 Motion Detection
- 13 Active Deterrence
- 14 Smart Motion Detection
- 15 Face Detection
- 16 Managing Passwords and User Accounts
- 17 Using the Main Menu
- 17.1 Main Menu Overview
- 17.2 Setting the Monitor Resolution (Display)
- 17.3 Configuring Sequence Mode
- 17.4 Camera Menu
- 17.5 Information Menu
- 17.5.1 Version Information
- 17.5.2 Hard Drive Information
- 17.5.3 BPS
- 17.5.4 System Log
- 17.5.5 Alarm
- 17.5.6 Online Users
- 17.5.7 Network Load
- 17.5.8 Network Test
- 17.5.9 Saving Your System Configuration to a USB Thumb Drive
- 17.5.10 Restore Default Settings
- 17.5.11 Upgrading Firmware Manually
- 17.5.12 Automatic Firmware Upgrades
- 17.6 Network Settings
- 17.6.1 Selecting DHCP or Static IP Address (TCP/IP)
- 17.6.2 Configuring System Ports (Connection)
- 17.6.3 Configuring Email Alerts
- 17.6.4 Configuring Switch Settings (Advanced)
- 17.6.5 P2P Setting
- 17.6.6 Performing Smart Search for Safeguard
- 17.6.7 Configuring Smart Plan
- 17.6.8 Configuring Safeguard
- 17.6.9 Configuring Video Loss Settings
- 17.6.10 Configuring Hard Drive Warnings
- 17.6.11 Configuring Network Warnings
- 17.6.12 Searching Event Logs
- 17.6.13 Configuring Pre-Recording
- 17.6.14 Formatting the Hard Drive
- 17.6.15 Configuring Hard Drive Type
- 17.6.16 Configuring Record Estimate (Recording Calculator)
- 17.6.17 FTP (Advanced)
- 17.6.18 Configuring General System Settings
- 17.6.19 Configuring Holidays
- 17.6.20 Configuring IP Filter
- 17.7 Shutdown
- 18 Connecting Remotely using the Lorex Home Mobile App
- 19 Smart Home & Voice Assistance
- 20 Pan/Tilt/Zoom (PTZ) Cameras
- 21 Connecting Audio Devices
- 22 Replacing the Hard Drive
- 23 DDNS Setup (Advanced)
- 24 Troubleshooting
- 24.1 Top Reasons Your Lorex Camera May Lose Video or Go Black
- 24.1.1 Going over PoE budget will result in video loss
- 24.1.2 When to use a PoE Switch?
- 24.1.3 Not enough power or total loss of it
- 24.1.4 Power surge and interference
- 24.1.5 Not supported display output
- 24.1.6 Twisted, bent or damaged cables
- 24.1.7 Outdated firmware and hardware
- 24.1.8 Issue with compatibility
- 24.1.9 Low internet bandwidth
- 24.1 Top Reasons Your Lorex Camera May Lose Video or Go Black
- 25 Technical Specifications
- 26 Notices
Playback10
3. Channel Selection: Select channels and video quality for playback. You can check up to 4
channels for playback in mainstream (
) and up to 8 channels for playback in substream (
).
4. Viewing Modes:
•
Not supported
•
Bookmark List: Shows all bookmarked recordings for a single channel on the se-
lected date (requires bookmarked recordings — see below for details).
•
File List: Shows all available recordings for the selected date and channel(s) in
list format.
5. Playback Bar Time Scale: Select the length of the time period shown on the playback bar.
6. Recording Type Filters: Click to show/hide recording types.
7. Sync: Select up to 4 channels for a synchronized playback. If the sync option is enabled, all
selected channels will playback video at the same time. The sync option makes it easy to
compare recordings from different cameras.
8. Playback Bar: Click inside the bar to select a playback time.
#LX400113; r. 9.0/57192/57197; en-US 27