User's Manual
Table Of Contents
- 1 Important Safeguards
- 2 Package Contents
- 3 Recorder Overview
- 4 Basic System Setup
- 5 Camera Installation
- 6 Using the Mouse
- 7 Setting the Date & Time
- 8 Using the On-Screen Display
- 9 Recording
- 10 Playback
- 11 Backup
- 12 Motion Detection
- 13 Active Deterrence
- 14 Smart Motion Detection
- 15 Face Detection
- 16 Managing Passwords and User Accounts
- 17 Using the Main Menu
- 17.1 Main Menu Overview
- 17.2 Setting the Monitor Resolution (Display)
- 17.3 Configuring Sequence Mode
- 17.4 Camera Menu
- 17.5 Information Menu
- 17.5.1 Version Information
- 17.5.2 Hard Drive Information
- 17.5.3 BPS
- 17.5.4 System Log
- 17.5.5 Alarm
- 17.5.6 Online Users
- 17.5.7 Network Load
- 17.5.8 Network Test
- 17.5.9 Saving Your System Configuration to a USB Thumb Drive
- 17.5.10 Restore Default Settings
- 17.5.11 Upgrading Firmware Manually
- 17.5.12 Automatic Firmware Upgrades
- 17.6 Network Settings
- 17.6.1 Selecting DHCP or Static IP Address (TCP/IP)
- 17.6.2 Configuring System Ports (Connection)
- 17.6.3 Configuring Email Alerts
- 17.6.4 Configuring Switch Settings (Advanced)
- 17.6.5 P2P Setting
- 17.6.6 Performing Smart Search for Safeguard
- 17.6.7 Configuring Smart Plan
- 17.6.8 Configuring Safeguard
- 17.6.9 Configuring Video Loss Settings
- 17.6.10 Configuring Hard Drive Warnings
- 17.6.11 Configuring Network Warnings
- 17.6.12 Searching Event Logs
- 17.6.13 Configuring Pre-Recording
- 17.6.14 Formatting the Hard Drive
- 17.6.15 Configuring Hard Drive Type
- 17.6.16 Configuring Record Estimate (Recording Calculator)
- 17.6.17 FTP (Advanced)
- 17.6.18 Configuring General System Settings
- 17.6.19 Configuring Holidays
- 17.6.20 Configuring IP Filter
- 17.7 Shutdown
- 18 Connecting Remotely using the Lorex Home Mobile App
- 19 Smart Home & Voice Assistance
- 20 Pan/Tilt/Zoom (PTZ) Cameras
- 21 Connecting Audio Devices
- 22 Replacing the Hard Drive
- 23 DDNS Setup (Advanced)
- 24 Troubleshooting
- 24.1 Top Reasons Your Lorex Camera May Lose Video or Go Black
- 24.1.1 Going over PoE budget will result in video loss
- 24.1.2 When to use a PoE Switch?
- 24.1.3 Not enough power or total loss of it
- 24.1.4 Power surge and interference
- 24.1.5 Not supported display output
- 24.1.6 Twisted, bent or damaged cables
- 24.1.7 Outdated firmware and hardware
- 24.1.8 Issue with compatibility
- 24.1.9 Low internet bandwidth
- 24.1 Top Reasons Your Lorex Camera May Lose Video or Go Black
- 25 Technical Specifications
- 26 Notices
Basic System Setup4
4.4 STEP 4: Connect monitor
Connect the recorder to a monitor using the included HDMI cable (supports up to 4K resolution).
OR
Connect the recorder to a monitor using a VGA cable (not included - supports up to 1080p
resolution).
CAUTION
If you need to switch monitors, make sure you set the recorder to an output resolution supported by the new
monitor before switching. See 17.2 Setting the Monitor Resolution (Display), page 59 for details.
4.5 STEP 5: Connect power
Use the included power adapter to connect the recorder to a nearby outlet.
4.6 STEP 6: Upgrade Firmware to Latest Version (If Available)
If a firmware upgrade is available, you will be asked to install it once the system starts up. It is
recommended to upgrade your system firmware and client software or mobile apps to the latest
version to ensure remote connectivity to the system and support newly-developed features.
NOTE
You must connect your recorder to a router with Internet access in order to get automatic firmware upgrades.
#LX400113; r. 9.0/57192/57197; en-US 7