Quick Start Guide
LNWDB1_QSG_EN_R1
Doorbell Password:
Next, you will complete the wiring for your new doorbell.
1
Loop the power cables around the
power ports of the doorbell.
STEP 3: Wiring the doorbell
3
Push the wiring through the hole in the
wall or door frame. Slide the doorbell
down so the plastic tab on the doorbell
locks into the notch on the mounting
bracket.
2
Use the included screws (×2) to
secure the power cables.
NOTE
If the power cables in the wall are not long enough,
use the optional power cable connectors and wire caps.
STEP 4: Wiring the chime
You must determine the type of doorbell chime you
have in your home: electronic or mechanical.
Not sure? If your doorbell chime is a classic
*ding-dong* sound, chances are your chime is
mechanical. If you are still not sure, remove the
cover panel of your chime box - if you nd spring-
loaded levers and a physical metal chime, you have
a mechanical chime.
For users with a mechanical chime, follow the extra
steps below to complete the installation.
For mechanical chime owners:
1. Remove the cover panel of your doorbell chime
box.
2. Loosen the screws labeled FRONT and TRANS
using the Phillips end of the included screwdriver.
Do not remove the screws, and be sure not to
detach any connected wiring.
3. Connect the included chime kit to the green terminal on
the end of the included wiring as shown below.
REAR TRANS
FRONT
STEP 5: Connecting to the Lorex Home app
4. Connect the wiring from the chime kit to the FRONT
and TRANS connectors in the chime box. Ensure that
the existing wiring stays connected as well.
NOTE: You may connect either wire to either
connector.
5. Mount the chime kit to the inside of your chime box, or
along the cover plate, using the included double-sided
tape.
IMPORTANT: Ensure the chime kit and wires are not
touching the chimes or any moving components inside
the chime box, or the doorbell chime will not sound
correctly.
Finalize the physical installation of the doorbell and begin setup
on the Lorex Home app.
1. Download and install the free Lorex Home app
from the App Store or Google Play Store.
2. Tap the Lorex Home icon to launch the app. Tap
Sign up, then follow the on screen prompts to
create an account. Record your account details
below:
Email:
Account Password:
3. Reconnect power to the doorbell at the breaker.
4. Once the status LED on the doorbell is solid blue, tap +.
5. Scan the QR code on the back of the doorbell using your mobile
device’s camera.
NOTE: If your mobile device cannot scan the QR code, tap
Manually enter Device ID.
6. Press the RESET button on the back of the doorbell to enable the
device hotspot.
7. Tap Next in the Lorex Home app once the hotspot is enabled and
the LED strip is pulsing.
8. The app will connect your mobile device to the doorbell’s
hotspot.
9. Create a secure password for the camera. Record your camera
password below:
10. Select your Wi-Fi network from the list, then enter the password to
connect your doorbell to the Internet.
11. Once the status LED on the doorbell is solid blue, tap Next to add
the doorbell to your Lorex Home account.
12. Set a name for the doorbel and congure date & time preferences,
then tap Complete to nish the setup.
13. Insert the included security screw
through the mounting bracket and into
the screw hole on the bottom of the
doorbell. Fasten tightly using the star-
shaped end of the included screwdriver
to complete the installation.
Lorex Home Overview
Back to
previous
screen
Device
settings
Device name
Pause / Play FullscreenViewing
modes
Mute /
Unmute
Streaming
quality*
Play back
recorded
video
Snapshot
Manual
recording
2-way audio: tap to speak, tap again to disable
Overview of the live viewing screen and controls in the Lorex Home
app. For complete instructions on using the app, see the Lorex Home
app manual on your product page at lorex.com.
* Change the streaming quality to SD (Standard Denition) to conserve bandwidth while
watching live video. This will not impact the quality of recorded video.
Live viewing screen:Live viewing screen:
Calling screen:
Answer
Reject