User's Manual

V261LC_QSG_EN_R1
HD Video Floodlight
To prepare for installation:
Before assembly, there are important preparations to make.
• TURN OFF POWER TO YOUR
FLOODLIGHT CIRCUIT AT THE
FUSEBOX TO ENSURE NO
POWER IS BEING SENT. If you
are unsure of which breaker
controls the circuit, then turn
off the main power switch.
If you do not know where
your breaker is or how to turn
off power, consult a licensed
electrician.
• Verify that the supply voltage
is correct. Connect xture to a
100 VAC~240 VAC 50/60 Hz
power source.
• DO NOT connect oodlight to a
dimmer switch or timer.
• If you are not replacing a light
xture, you will need to run
power cabling to the install
location, and purchase a
UL listed junction box for a
licensed electrician to install.
LED Indicator
Quick Start Guide
Series
lorex.com
2k Outdoor Floodlight Camera
Package Contents
STEP 1: Preparation
Need Help?
Visit us online for up-to-date software
and complete instruction manuals
Click on the Downloads tab
4
Visit lorex.com
Search for the model
number of your product
Click on your product
in the search results
3
2
1
Copyright © 2020 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to
modify product design, specications and prices, without notice and without incurring
any obligation. E&OE. All rights reserved.
Mounting Screws &
Anchors (×3)
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use and handling of the product.
• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh,
chemical-based cleaners.
• Use the product within given temperature, humidity and voltage levels noted in the
product’s specications.
• Do not disassemble the oodlight.
Safety Precautions
• Always follow code standards when installing wired connections.
• This oodlight camera must be installed on a wall and a UL listed junction box.
• This oodlight includes an Auto Mechanical IR Cut Filter. When the camera
changes between Day/Night viewing modes, an audible clicking noise may be
heard from the oodlight. This clicking is normal, and indicates that the camera
lter is working.
• Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation
assumes no liability for use of its products that does not conform with local laws.
Disclaimers
CAUTION
Risk of re.
Do not install camera near ammable or combustible surfaces.
Risk of electrical shock.
Disconnect the power at the fuse box before installation.
Hooks
Mounting Bracket
Scan for
Lorex Home APP
11.4”
290mm
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
FCC Notice
Product Overview
PIR motion sensor
Speaker
Microphone
Camera
IR LED
Top cover
Light sensor
Memory slot*
Reset button**
Floodlights
Adjusting knobs
Wire Caps (×3)
Bracket Screws
A and B (×2)
Phillips Machine Screw
A
B
32 Feet
12.8” / 325mm
7.3” / 185mm
Mount the oodlight camera 10 feet (3 meters) high with the
motion detector levelled to the ground for optimizal detection
of human-sized objects as far as 32 feet (10 meters).
Recommendation:
Front Panel
Back Panel
Behavior Meaning
(steady)
Operating correctly.
(ashing)
Ready for connection.
(ashing rapidly)
Mobile device is attempting to connect to the camera.
(steady)
Device malfunction. Try resetting the camera and repeating the setup.
(ashing)
Network connection failed. Try resetting the camera and repeating the setup.
(ashing rapidly)
Memory slot error. Try removing and re-inserting the included memory slot card,
or try a different card.
(alternating)
Firmware upgrade in progress.
* To access the memory slot and reset button, twist left to open the top cover.
** To reset the camera, hold down the reset button until the chime sounds and the LED Indicator turns red.
V261LC_QSG_EN_R1.indd 1V261LC_QSG_EN_R1.indd 1 2020-03-03 5:40:22 PM2020-03-03 5:40:22 PM
W452AS
The user manual for local area network devices shall contain instructions
related to the restrictions mentioned in the above sections, namely that:
(i) the maximum antenna gain permitted for devices in the bands 5250-
5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
(ii) the maximum antenna gain permitted for devices in the band 5725-
5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point
and non point-to-point operation as appropriate.
(i)ÿle gain d'antenne maximal autorisé pour les appareils dans les
bandes 5250-5350 MHz et 5470-5725 MHz doivent respecter le pire
limiter; et
(ii)ÿle gain d'antenne maximal autorisé pour les appareils dans la
bande 5725-5825 MHz doivent respecter le pire limites spécifiées pour
le point-à-point et l'exploitation non point à point, le cas échéant.
Users should also be advised that high-power radars are allocated as
primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650
-5850 MHz and that these radars could cause interference and/or
damage to LE-LAN devices.
Les utilisateurs de radars de haute puissance sont désignés utilisateurs
principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz
et 5650-5850 MHz et que ces radars pourraient causer du brouillage
et/ou des dommages aux dispositifs LAN-EL.