Quick Start Guide

V261LC_QSG_EN_R1
Next, install the oodlight’s mounting br
acket.
Next, install the oodlight camera.
STEP 2: Secure the Mounting Bracket STEP 4: Secure the Floodlight
1
Hang the oodlight camera
from the
mounting bracket using
the supplied hooks.
2
The copper wire from the camera is ground wire.
Connect the ground wire to the existing ground
wire inside of your junction box.
Use the supplied wire cap.
In the case that you ar
e not wiring from a junction
box, twist your ground wire around the green
screw on the bracket.
3
The white wire from the camera is neutral
wire. Use a wire cap to connect the neutral
wires from the camera and junction box.
The black wire from your camera is a hot
wire. Use a wire cap to connect the hot
wires from the camera and junction box.*
1. With the power shut off, remove the existing light xture and
bracket from the wall.
2. Disconnect the wires.
1. Carefully push all the wir
es through the middle opening of the bracket
into the junction box, and secure the oodlight camera through the
middle hole using the Phillips machine screw.
In the case that you ar
e installing the oodlight camera directly to the
bracket, t the wires into the back openings of the camera.
Hook one end into your oodlight camera.
Hook the other end into the br
acket.
Overview of Lorex Home app
STEP 3: Connect the Wires
Back to
pr
evious
screen
Device
settings
Device name
Lorex Floodlight
P
ause / Pla
y Fullscreen
Viewing
modes
Mute /
Unmute
Str
eaming
quality*
Play back
r
ecorded
video
Snapshot
Siren
Manual
recor
ding
Light
2-way audio: tap t
o speak, tap again to disable
* Change the str
eaming quality to SD (Standard Denition) to conserve bandwidth while
watching live video. This will not impact the quality of recorded video.
Live viewing scr
een:
To wir
e the oodlight:
To install directly to a junction box:
To install directly on a wall:
* Power wir
e colors in your home may be
different. In such a case consult a licensed
electrician.
IMPORTANT: Properly ground xture.
Floodlight Passwor
d:
1. Once the status LED on the oodlight is ashing green, tap
Next in
the Lorex Home app. The app will connect your mobile device to the
oodlight’s hotspot.
2. Create a secure password for the oodlight. Record your oodlight
password below and store in a secure location:
3. Select your Wi-Fi
network from the list,
then enter the Wi-Fi
password to connect
your oodlight to the
Internet.
T
o link the oodlight:
4. Once the status LED on the oodlight is solid green, tap
Next to add
the oodlight to your Lorex Home account.
5. Set a name for the oodlight and congure date & time preferences,
then tap Complete.
NOTE
: Be sure to follow the “Front” / ”Up” directions on the mounting bracket.
3. Run the wires thr
ough the
middle of the supplied
mounting bracket.
4. Secure the mounting
br
acket to your junction
box using one of the
bracket screws, A or B
depending on which
size ts.
STEP 5: In-app Setup
Next, connect the oodlight camera t
o the Lorex Home app.
NOTE: If the Wi-Fi
connection is weak,
try moving your router
closer or adding a Wi-Fi
extender.
1. Download and install the free Lorex Home app from
the App Store or Google Play Store.
2. Tap the Lorex Home icon to launch the app. Tap Sign
up, then follow the on screen prompts to create an
account. Record your account details below and
store in a secure location:
Email:
Account Passwor
d:
3. Wait for the oodlight t
o start up. This may take up to 5 minutes after
reconnecting power at the breaker.
To scan the QR code:
4. Once the status LED on
the oodlight is ashing
green, tap
+ in the Lorex
Home app.
5. Scan the QR code on the
side of the oodlight
camera using your
mobile device’s camera.
NOTE:
If your mobile
device cannot scan the
QR code, tap Manually
enter Device ID.
2. Adjust the lens and light angle using the adjusting knobs.
3. To enfor
ce a water resistant seal, apply silicone compound around the
entire perimeter where the junction box is attached to the bracket.
4. You ma
y now restore power at the fusebox.
NOTE: If
the status LED on the oodlight camera does not turn on, check
to make sure wiring is done correctly.
1.
2.
3. Use the mounting brack
et
as a template to mark 3
holes in a triangular pattern.
4. Use a 1/4” drill bit to drill in
the mark
ed holes.
5. Gently tap the supplied
mounting anchors int
o
the drilled holes with a
hammer.
6. Align the br
acket and use
a Phillips head screwdriver
to secure the supplied
mounting screws into the
mounted anchors.
A
B
V261LC_QSG_EN_R1.indd 2V261LC_QSG_EN_R1.indd 2 2020-03-03 5:40:28 PM2020-03-03 5:40:28 PM
FCC
WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED WARNING
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102
énoncée dans un autre environnement.cette eqipment devrait être installé et exploité avec distance
minimale de 20 entre le radiateur et votre corps.