User's Manual
Table Of Contents
- Terminology
- Introduction
- Installation
- Software configuration
- Prepare your PC to configure the WLAN Broadband Router
- Connect to the WLAN Broadband Router
- Management and configuration on the WLAN Broadband Router
- Status
- Setup Wizard
- Operation Mode
- Wireless - Basic Settings
- Wireless - Advanced Settings
- Wireless - Security Setup
- Wireless - Access Control
- WDS Security Setup
- WDS AP Table
- WDS Settings
- Site Survey
- WPS Settings
- LAN Interface Setup
- WAN Interface Setup
- Firewall - Port Filtering
- Firewall - IP Filtering
- Firewall - MAC Filtering
- Firewall - Port Forwarding
- Firewall - URL Filtering
- Firewall - DMZ
- Management - Statistics
- Management - DDNS
- Management - Time Zone Setting
- Management - Denial-of-Service
- Management - Log
- Management - Upgrade Firmware
- Management - Save/ Reload Settings
- Management - Password Setup
- FREQUENTLY ASKED QUESTIONS (FAQ)
- What and how to find my PC’s IP and MAC address?
- What is Wireless LAN?
- What are ISM bands?
- How does wireless networking work?
- What is BSSID?
- What is ESSID?
- What are potential factors that may causes interference?
- What are the Open System and Shared Key authentications?
- What is WEP?
- What is Fragment Threshold?
- What is RTS (Request To Send) Threshold?
- What is Beacon Interval?
- What is Preamble Type?
- What is SSID Broadcast?
- What is Wi-Fi Protected Access (WPA)?
- What is WPA2?
- What is 802.1x Authentication?
- What is Temporal Key Integrity Protocol (TKIP)?
- What is Advanced Encryption Standard (AES)?
- What is Inter-Access Point Protocol (IAPP)?
- What is Wireless Distribution System (WDS)?
- What is Universal Plug and Play (uPNP)?
- What is Maximum Transmission Unit (MTU) Size?
- What is Clone MAC Address?
- What is DDNS?
- What is NTP Client?
- What is VPN?
- What is IPSEC?
- What is WLAN Block Relay Between Clients?
- What is WMM?
- What is WLAN ACK TIMEOUT?
- What is Modulation Coding Scheme (MCS)?
- What is Frame Aggregation?
- What is Guard Intervals (GI)?
- Configuration examples
Reset Settings to
Default
Click the Reset button to reset the configuration parameter
to factory defaults.
Management - Password Setup
This p
age is used to set the accou
nt to access the web server of Access Point. Empty user name and password will
disable the protection.
Item Description
User Name Fill in the user name for web management login control.
New Password Fill in the password for web management login control.
Confirmed
Password
Because the password input is invisible, so please fill in the
password again for confirmation purpose.
Apply Changes Clear the User Name and Password fields to empty, means to
apply no web management login control.
Click the Apply Changes button to complete the new
configuration setting.
Reset Click the Reset button to abort change and recover the previous
configuration setting.
FREQUENTLY ASKED QUESTIONS (FAQ)
Enter topic te
xt here.
What and how to find my PC’s IP and MAC addre
ss?
IP addre
ss is the identifier for a compute
r or device on a TCP/IP network. Networks using the TCP/IP protocol route
messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written
as four numbers separated by periods. Each number can be zero to 255. For example, 191.168.1.254 could be an IP
address.
The MAC (Media Access Control) address is your computer's unique hardware number. (On an Ethernet LAN, it's the
same as your Ethernet address.) When you're connected to the Internet from your computer (or host as the Internet
protocol thinks of it), a correspondence table relates your IP address to your computer's physical (MAC) address on
the LAN.
51