Installation & Assembly

1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
3) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
4) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raise dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
After following the above steps. Never connect ground wire
to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
5) Make wire connections. Reference chart below for correct
connections and wire accordingly.
6) Push fixture into wall, carefully passing mounting screws
through the holes.
7) Screw the lock-up knobs onto mounting screws. Tighten to
secure fixture to the wall.
8) Align a support arm through a hole on the top trim and
through a hole in the socket housing. Secure into place by
screwing in a support knob at the top of socket housing.
9) Repeat step 8 for remaining support arms.
10) Insert recommended bulb.
11) Set glass onto foam pad of bottom trim.
12) Align bottom of support arms through bottom trim holes.
(Passing the glass past bulb, through top trim ring, and
resting with the top of the glass inside socket housing).
13) While holding in place, secure by screwing in remaining
support knobs through the bottom trim to the arm supports.
14) Repeat steps 8-13 to mount the remaining glass.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
FRONT VIEW
VISTA FRONTAL
SOCKET HOUSING
CAJA DEL ZÓCALO
SUPPORT KNOB
PERILLA
DE APOYO
CANOPY
ESCUDETTE
MOUNTING STRAP
ABRAZADERA
DE MONTAJE
MOUNTING SCREW
TORNILLOS
DE MONTAJE
SIDE VIEW
VISTA LATERAL
WIRE NUTS
TUERCAS
DE MARIPOSA
TOP TRIM
MOLDURA
SUPERIOR
ARM SUPPORT
BRAZO
DE APOYO
LOCK-UP KNOBS
PERILLAS
DE SUJECIÓN
LOCKWASHER
ARANDELA DE
SEGURIDAD
STRAP
MOUNTING
SCREW
TORNILLO DE
MONTAJE DE
LA ABRAZADERA
GLASS
VIDRIO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.