Assembly Instructions Caution: You must read this before you proceed Please look in the Seat Panel for hardware packs Caution: This is NOT a TOY. Keep your child / children at bay during the assembly process. Whenever moving or lifting this and to prevent any possible damage to it, two adults are needed to execute this action.
Parts List Label Description Picture QTY A Seat Panel 1 B Backrest 1 C 1 D Left Armrest 1 E Right Armrest 1 F KD Slat 1 G Folding Support Bar 2 H Tray 1 Page 2 OF 9
Label Picture Description QTY 1 Bolt ( M8x35mm ) 7 2 Sleeve Nut ( M8x15mm ) 7 3 Long Screw ( M7x70mm ) 3 4 Short Screw ( M7x40mm ) 3 5 Screw (M4x30mm) (Use with Screwdriver) 7 6 Plastic Washer 7 7 Allen Key 2 8 Screwdriver (Not provided) Before Beginning Assembly: Page 3 OF 9
Assembly Steps OVERVIEW Backrest(B) Left Armrest (D) Right Armrest (E) Seat Panel (A) Folding Support Bar (G) Pre-fixed Front Leg (C) KDSlat(F) FRONT FACING Tray (H) This has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 2 8 F 5 A Place the Seat Panel(A) onto a clean, non-marring surface. Position the KD Slat(F) onto the Seat Panel(A) using Screws(⑤) and a Screwdriver (⑧) as shown above Do not fully tighten the Screws Step 3 A 7 2 6 C 7 Turn the assemble in step 2 upside down as shown above. Attach the Pre-fixed Front Leg( C) to the Seat Panel(A) using Bolts( ①) Plastic Washers (⑥), Sleeve Nuts ②and the Allen Key (⑦) as shown above Do not fully tighten Bolts.
Step 4 C A G 1 6 7 2 Turn the Frame in Step 3 back right side up and place it in the position as shown in the picture above. Attach the Folding Support Bar(G) to the Seat Panel(A) using Bolts ( ① ), Plastic Washers (⑥), Sleeve Nuts (②) and the Allen Key (⑦). Do not fully tighten Bolts. Note: A Plastic Washer should be placed between the Seat Panel and the Folding Support Bar.
Step 6 Step 6.1 3 7 B Step 6. 2 7 1 D 6 C 2 7 A Open the Backrest(B) as shown in the picture above: 6.1) Secure the Left Armrest (D) to the Backrest (B) using Screws( 3) and the Allen Key ( ⑦) 6.1) Secure the Left Armrest (D) to the Pre-fixed Front Leg (C) using Bolts( ①), Plastic Washers ( ⑥ ), Sleeve Nuts (② ) and the Allen Key( ⑦) Do not fully tighten Bolts and Screws.
Step 8 In a sequential manner, tighten all Bolts and Screws at all joints until fully locked into position. Your chair is ready for use. This can only be used on a flat, level surface. Step 9 To Fold To Open This can be folded shut. To fold this , raise up the Backrest and fold the Seat with the Leg Frame as indicated by the arrows, until this folds shut. To open this , open the Backrest and Seat as indicated by the arrows, until this folds out and locks into position.
Page 9 OF 9
