Assembly Instructions Caution: You must read this before you proceed Adirondack CAUTION : This Adirondack is NOT a TOY. Keep your child / children at bay during the assembly process. For moving the Adirondack and to prevent damage to the Adirondack, two adults are needed to execute this action.
Parts List Label Picture Description QTY A Seat Panel 1 B Backrest 1 C 1 D Left Armrest 1 E Right Armrest 1 F KD Slat 1 G Folding Support Bar 2 Page 2 OF 9
Label Picture Description QTY 1 Bolt ( M8x35 ) 7 2 Sleeve Nut ( M8x15 ) 7 3 Long Screw ( M7x70 ) 3 4 Short Screw ( M7x40 ) 3 5 Screw (M4x30mm) (Use with Screwdriver) 5 6 Plastic Washer 7 7 Allen Key 2 8 Screwdriver Not provided Before Beginning Assembly: Page 3 OF 9
OVERVIEW Right Armrest (E) Backrest (B) Seat Panel (A) Left Armrest (D) Pre-fixed Front Leg (C) Folding Support Bar (G) KD Slat (F) FRONT FACING This Adirondack has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Adirondack parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 2 F A 8 5 Place the Seat Panel(A) onto a clean, non-marring surface. Position KD Slat(F) onto the Seat Panel(A) and attach using 4 Screws(⑤) and Screwdriver(⑧). Step 3 A 6 C Place the Seat Panel(A) as shown in the picture. Attach Pre-fixed Front Leg(C) to Seat Panel(A) using Bolts(①), Plastic Washers(⑥), and Sleeve Nuts(②) with Allen Keys( ⑦). Do not fully tighten Bolts. Note: The Plastic Washer should be placed between the Seat Panel and Pre-fixed Front Leg.
Step 4 6 A G 1 2 7 Place the Frame in Step 3 in the position as picture above. Attach Folding Support Bar(G) to Seat Panel(A) using Bolt(①), Plastic Washer(⑥), and Sleeve Nut(②) with Allen Keys( ⑦). Do not fully tighten Bolts. Note: Plastic Washer should be placed between Seat Panel and Folding Support Bar. Step 5 B 4 7 G Position Backrest(B) with mortise into housing of Folding Support Bar(G). Secure Folding Support Bar(G) to Backrest(B) using Short Screw(④) with Allen Key(⑦).
Step 6 Step 6.2 7 B 3 E 7 Step 6.1 1 2 6 C 7 Open Backrest(B) as indicated with the arrow. 6.1) Secure Right Armrest(E) to Pre-fixed Front Leg(C) by using Bolt( ① ), Plastic Washer(⑥), and Sleeve Nut( ②) with Allen Keys( ⑦). 6.2) Secure Right Armrest(E) to Backrest(B) using Long Screw( ③ ) with Allen Key(⑦). Do not fully tighten Bolts and Screws. Note: Plastic Washer should be placed between Left Armrest and Pre-fixed Front Leg. Repeat the same process with the Left Armrest (D).
Step 7 Your Adirondack is ready for use. This Adirondack can only be used on a flat, level surface. Step 8 To Fold To Open This Adirondack can be folded shut. To fold this Adirondack, raise up Backrest and fold Seat with Leg Frame as indicated by the arrows, by hand, until the Adirondack folds shut. To open this Adirondack, open Backrest and Seat as indicated by the arrows, by hand until the Adirondack folds out and locks into position.
Page 9 OF 9
