Assembly Instruction

ManualsBrandsLongshore Tides ManualsLantern Outdoor Wall LightingSheppard 3 - Bulb Seeded Glass Outdoor Wall Lantern

Package Contents

1of2

Thank you for purchasing

STEP 1 Install Shade-

A. Unscrew the Lock Screw, remove the Cage, the Glass Shade and the

Tab from the Fixture Body (A). Remove the Styrofoam from inside of

the shade.

B. Place Glass Shade into the Cage, secure by place the Tab into the

Cage press on the Glass Shade.

C. Set the Cage with Glass Shade into the Cap on the Fixture Body (A),

secure by threading the Lock Screw into the Cap, tighten until sung.

Figure 3

Figure 1

Mounting

Ball

Mounting

Screw

Hex Nut and

Lock Washer

STEP 2 Install Inner Backplate-

A. Pass the supply wires through the Crossbar Assembly (AA). Attach

the Crossbar Assembly (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included). Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 3 Fit Fixture Body to

Crossbar Assembly

A. Remove mounting balls from the

Crossbar Assembly (B). Fit the

Fixture Body (A) Crossbar

Assembly (B) and secure with

mounting balls. Note: The

backplate of the Fixture Body (A)

should be snug against the wall

surface and the mounting balls. If

not, adjust the length of the nipple

on the Crossbar Assembly (B) by

unscrewing the preassembled hex

nut and lock washer and then

screwing the mounting screws in or

out of the crossbar until the correct

length is achieved. Once the

backplate of the Fixture Body (A) is

secure, remove the mounting ball

and Fixture Body (A) and proceed

to Step 4.

Crossbar Assembly

Fixture

Body

Fixture Body

Cage

Tab

Glass Shade

Lock Screw

(3)CandelabraBase60W Maximum,Alternatebulb(3) 13WCFL

30-45minutes

Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are

present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement

parts.

Fixturecan onlybe mountedin thedirection indicatedon page2.

Warnings and Cautions

Assembly Instruction Sheet

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

STEP 4 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist

connectors until wires are tightly joined together. Wrap each

connection with approved electrical tape and carefully stuff all the

connected wires into the Outlet Box.

ToolsRequired:

BulbRecommended:

EstimatedAssemblyTime:

Preparation:

Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wire strippers,electrical tape,safety glasses.

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Tools Required: Bulb Recommended: (3) Candelabra Base 60W Maximum, Alternate bulb (3) 13W CFL Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
STEP 6 - Install Bulb White wire from supply White wire from fixture Black wire from supply (or Red) Black wire from fixture A. This fixture uses candelabra bulb with a candelabra screw base. Maximum 60 watts. B. Insert bulb and screw snugly into place. Ground wire from fixture Ground wire from supply Bulb Figure 4 Socket Figure 6 STEP 5 - Install Fixture Body A. Carefully tuck all wires into the outlet box and position the backplate of fixture body (A) over the outlet box.