Table Genie UHF U S E R M A N UA L Installation, Warranty and Service Information Long Range Systems, Inc. 4550 Excel Parkway, Suite 200 Addison, TX 75001 800.437.4996 • www.pager.
Table Of Contents Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the Programming Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using the Programming Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Global Configuration . . . . . . .
GETTING STARTED Software Installation Insert the software disk into the disk drive on your computer. The installation should auto-run. If not, navigate to the Installer.msi file located on the installation disk and run it manually. Step 1 – Once the installation wizard begins, you will see the screen shown below. Click 'Next' to continue.
Step 3 – This is the confirmation screen indicating that you are about to install the software.
Step 5 – This is the final step in the installation wizard. Click ‘Close’ to complete the installation process. Connecting the Programming Cable Included in your software kit, is a mini USB cable with an LRS programming adapter. Connect the LRS programming adapter to the mini USB cable. Connect the complete programming cable to an available USB port on your computer.
USING THE PROGRAMMING SOFTWARE Global Configuration The Global Configuration Settings are settings that will be programmed into all Table Genie units once the specific table information is uploaded to them. These settings should be configured before creating any tables under the Table Configuration tab. System Id In order to prevent other LRS paging systems in the area from conflicting with your LRS paging system, your pagers and Table Genies may be on a system ID other than the default of zero.
Low Battery Alert Enable When enabled, this feature will notify the pager of your choice when a Table Genie’s battery level drops below the specified threshold (threshold is in percent value).
Group Page Enable Enabling this feature will allow pagers that have been previously programmed into groups to be called by their group number simultaneously. Enabling this feature will not allow you to page any individual pager numbers that have been programmed below number 100. To program a Table Genie to page groups: • Enable group paging on the ‘Global Configuration’ tab. • When creating a new table (see programming Table Genies in the next section).
Table/Room No. This field is used to uniquely identify the Table Genie Unit being programmed. This is a free form field and can be alpha, numeric, or alpha-numeric characters. The name given to the Table Genie is part of the message sent to the pager when a page is sent allowing the person responding to the page know where the page originated from. Manager Pager No.
Saving and Loading Your System Configuration Once all tables have been configured and saved to the ‘Table Configuration’ tab, it is recommended that you save your system configuration to a file on your computer. This will create a backup that can be loaded at a later date if need be. Backing up your configuration will save you from having to recreate your table list should something happen to your system.
3. Press Program 4. For battery operated Alpha Pagers, insert the battery. For rechargeable Alpha Pagers, remove the pager from a charger. 5. At Programming Instructions screen, press Program. 6. User should hear 13 beeps for programming.
Programming and Reading Table Genie Units Once the global configuration has been set and the tables have been configured, you are now ready to begin programming the Table Genie units. To program a Table Genie with a specific table configuration: 1. Connect the programming cable to the computer (see Connecting the Programming Cable). 2. Remove the battery door compartment and the battery from the Table Genie. Remove Battery Release Tab of Battery Cover Pull in Direction of Arrows 3.
4. While holding the programming cable in place, click on the ‘Program’ link for the desired table. 5. You will see a pop-up screen with continuing instructions 6. While continuing to hold the programming cable in place, click on the program button. 7. You will see a series of screens as the Table Genie is being programmed followed by a confirmation that the programming has succeeded.
To read a previously programmed Table Genie, follow steps 1-3 shown above and click on ‘Read Device’. While holding the programming cable in place, click ‘Read Device’. Once the device is successfully read, you will see a pop-up screen showing all of the settings loaded on that particular Table Genie unit.
Cleaning Instructions For LRS Paging Equipment Cleaning: LRS pagers and equipment are made from industrial-strength, polycarbonate material. However, this material is susceptible to hairline cracking if non-approved cleaners are used. When cleaning LRS pagers, we recommend only using ISOPROPYL ALCOHOL-BASED CLEANERS. To clean the equipment: 1. Take a clean rag and an isopropyl-alcohol based cleaner. 2. Soak the clean rag with the isopropyl alcohol cleaner. 3. Wipe down the pagers or equipment.
Warranty Long Range Systems, Inc. warrants this product against any defects that are due to faulty material or workmanship for a one-year period after the original date of consumer purchase. This warranty does not include damage to the product resulting from accident, misuse or improper electrical connection. If this product should become defective within the warranty period, we will repair or replace it with an equivalent product, free of charge. LRS will return your product via UPS ground shipping.
FCC INFO The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
