User's Manual

Pairing with a
Bluetooth
®
Phone
You must pair your headset to a
Bluetooth
®
Mobile Phone.
For more details, refer to your mobile phone user guide or contact the phone’s manufacturer.
1. Turn on your phone. Make sure the battery is charged in both devices. Turn off the Headset.
2. Press and hold the Multi-function button until the headset indicator
light fl ashes blue and red (about 10 seconds).
3. The Headset is now in Pairing mode. Release the button. The indicator
light will continue fl ashing red and blue.
4. Follow the pairing instructions for your
Bluetooth
®
phone. Typically,
this is done by going to a ‘setup’ or ‘connect’ menu and then selecting
the options to ‘discover’
Bluetooth
®
devices.
5. Your phone should fi nd the ‘
Logitech HS02-Vxx
’ headset.
Confi rm to pair.
6. Your phone should prompt you for a passkey or
PIN
.
The PIN/passkey is:
0000
.
7. If pairing was successful, the Headset LED will fl ash blue.
8. If pairing fails turn the headset and phone off and repeat the process.
9. Red and blue fl ashing will return to stand-by mode (blue fl ashing LED) if not paired in 2 minutes.
Comfort & Fit
1. Flip the earpiece and slide the
headset to fi t either ear.
2. Rotate the earpiece and slide the
headset over ear to your comfort.
3. Rotate the microphone boom so
it is pointing toward the corner of
your mouth.
Please see www.logitech.com for
more information.
Using your Headset
Turning the headset on and off:
Push and hold the multi-function button for 4 seconds. A blue light will fl ash when on.
Answering/ending a call:
Press the multi-function button.
Muting a call:
Press and hold Volume up for
3
seconds. A repeating beep will indicate that the microphone is muted. Quick-Press of
Volume up or down to discontinue mute.
Charging the Headset
1. Turn off the headset and connect the power adapter.
2. Plug the power adapter to an electrical outlet.
3. The LED will be orange when charging. If the LED is not
orange, the connection is not suffi cient.
4. When the LED turns off, your headset is fully charged.
Charging can take up to
3
hours.
Setup – Pairing your Headset
Wearing and Using your Headset
3
English
4
English
Headset Operation
Activation
LED Status
Sounds
Turning On
Press multi-function button fo
r more than 3 seconds
5 BLUE flashes
brief low-to-high tone
Receiving incoming call
None
- Automatic
3 repeating BLUE flashes
melody increases in volume
Answering call
Briefly press multi-function button
3 repeating BLUE flashes
single beep when answered
During call
None
- Automatic
4 repeating BLUE flashes
no beep
Mic Mute-on during call
Press + volume button more than 2 seconds
4 repeating BLUE flashes
double-beep every 30 seconds
Ending mic mute
Press + or
- volume button briefly
4 repeating BLUE flashes
single beep
Ending call
Press multi-function button briefly
3 repeating BLUE flashes
single beep
Pairing
Option 1
Option
2
Wh
ile off, press MFB for about 8 seconds until R
ED
and BL
UE flashes (times out after 2
minutes i
f no
pairing)
From Standby, press MFB for about 8 seconds until
RED and B
LUE flashes (times out after 2 minutes if
no pairing)
no pairing)
Alternating RED and BLUE flashes
Repeating BLUE flash when
paired
Alternating RED and BLUE flashes
Repeating BLUE flash when
paired
paired
single high-low tone beep
No beep after pairing
single high-low tone beep
No beep after pairing
Standby or connected
Non
e
1 or 3 repeating BLUE flashes
None
Voice Dialing
In standby mode, press multifunction butt
on, say
n
ame (stored in phone) after tone
4 repeating BLUE flashes
single beep
Low Battery
(<30 minutes)
None
- Automatic
RED flashes
last 30 minutes
Turning off
Press multi-function button for more than 3 seconds
5 RED flashes
high-to-low tone
Charging
Connection to power adapter charger and plugging
into electrical outlet
Continuous ORANGE
(Some funtions are phone dependent)
1
2
3
Multi-function
button