Size: 84 x 118.
According to the European WEEE directive, electrical and electronic equipment must not be disposed with consumers waste. Its components must be recycled or disposed apart from each other. Otherwise contaminative and hazardous substances can pollute our environment. You as a consumer are committed by law to dispose electrical and electronic devices to the producer, the dealer, or public collecting points at the end of the devices lifetime for free. Particulars are regulated in national right.
2.0 Introduction When BT0024 is used as a Bluetooth transmitter, it can be connected to your walkman or PC to wirelessly transmit the music to your Bluetooth stereo receiver (Such as Bluetooth stereo headset, Bluetooth stereo speaker and so on). When it is used as a Bluetooth receiver, it can be connected to your common stereo receiver for wireless playing music from your Bluetooth audio player. 2.1 Feature: Switch freely between Bluetooth transmitter and Bluetooth receiver 3.
2.3 Package Contents 1 x Bluetooth Audio Transmitter & Receiver 1 x USB Charging Cable 1 x 3.5mm Male to Male Audio Cable 1 x User manual 3.0 Installation 3.1 Overview 1. Multi-function button (MFB): Switching on/off, pairing 2. Charging jack 3. LED indicator 4. 3.5mm audio jack 5. TX/RX switch 6. 3.5mm to 3.5mm audio cable 3.2 System Requirements a) When BT0024 is used as a Bluetooth transmitter, you need to prepare an audio player with 3.
3.3 Charging the built-in Battery First time charging: Please charge the battery fully before use the transmitter. Low battery: When the red LED flashes during use, the battery is low power and needs to be charged. 1. Plug charger or charging cable into the standard AC power socket 2. Plug other end of charger or charging cable into charging port of BT0024 RED light on → Charging RED light off → Charging finished 3. It takes about 2.5 hours to finish charging 3.
1. Switching on/off the transmitter Function Operation Switching on Press button for transmitter 3-4 seconds Switching off Press button for transmitter 3-4 seconds LED indicator Blue LED is on for 1second Red LED is on for 1 second and then off 2. Pairing with a Bluetooth device After the transmitter connecting to a Bluetooth stereo receiver, you can enjoy music wirelessly. Before pairing, please make sure your Bluetooth stereo receiver supports Bluetooth A2DP profile.
3. Reconnecting to a Bluetooth device 1). Automatic connecting Every time the transmitter is switched on, it will automatically connect to last connected device. 2). Manual connecting When the transmitter is in standby mode and doesn’t connect to any devices, short press button once, it will automatically connected to last connected device. 3).
RX Mode Selecting mode: Please turn the TX/RX switch to RX mode before switching on BT0024. Note: TX or RX mode cannot be changed after switching on BT0024. 1. Switching on/off the receiver Function Operation Switching on Press button for receiver 3-4 seconds Switching off Press button for receiver 3-4 seconds LED indicator Blue LED is on for 1second Red LED is on for 1 second and then off 2.
Pairing with a Bluetooth cell phone Please make sure your cell phone is Bluetooth-enabled. Specific pairing steps may vary with different models of cell phones. Please refer to your cell phone’s user’s manual for further information. The general pairing steps are as follows: 1). Keep the receiver and Bluetooth cell phone within 1 meter when pairing 2). Enter the receiver’s pairing mode (refer to “How to enter pairing mode”) 3).
stereo headset or stereo speaker with a 3.5mm to 3.5mm audio cable. Now you can listen to music and control pause/play of music. Function Status of the receiver Operation Pause Playing music Short press Play Pausing Short press button once button once 4. Reconnecting to a Bluetooth device Automatic connecting Every time the receiver is switched on, it will automatically connect to last connected device.
4.0 FAQs 1. What to do when BT0024 can’t be switched on? Please charge it. 2. What to do when BT0024 can’t pair and connect to a Bluetooth device? 1). Make sure Bluetooth stereo receiver supports A2DP 2). Make sure Bluetooth stereo receiver is placed within 5 meters 3). Make sure Bluetooth stereo receiver has already entered into pairing mode. 3. What to do when BT0024 can’t be switched off? Please charge it for about 2 seconds.