Product Info

Report No: CCISE191202301-V01
Shenzhen Zhongjian Nanfang Testing Co., Ltd. Project No.: CCISE1912023
No. B-C, 1/F., Building 2, Laodong No.2 Industrial Park, Xixiang Road,
Bao’an District, Shenzhen, Guangdong, China
Telephone: [phone] Fax: [phone], E-mail: [e-mail] Page 58 of 171
Spatial Peak
Uncontrolled Exposure/General Population
Averaged over 1g
 LTE 20MHz QPSK 100%RB Body SAR in Hotspot mode
Plot
No.
Band/Mode
Test
Position
CH.
Freq.
(MHz)
Ave.
Power
(dBm)
Power
Drift
(dB)
Tune-Up
Limit
(dBm)
Meas.
SAR
1g
(W/kg)
Scaling
Factor
Reported
SAR
1g
(W/kg)
Band2/RB#0
Back
18700
1860.0
23.21
-0.03
23.5
0.805
1.069
0.861
26
Band2/RB#0
Back
18900
1880.0
23.15
0.16
23.5
0.844
1.084
0.915
Band2/RB#0
Back
18900
1880.0
23.15
0.12
23.5
0.836
1.084
0.906
Band2/RB#0
Back
19100
1900.0
23.01
-0.10
23.5
0.821
1.119
0.919
Band2/RB#0
Bottom
18700
1860.0
23.21
-0.22
23.5
0.732
1.069
0.783
ANSI / IEEE C95.1 – SAFETY LIMIT
Spatial Peak
Uncontrolled Exposure/General Population
1.6 W/kg (mW/g)
Averaged over 1g
 WLAN 2.4GHz Body SAR in Hotspot mode
Plot
No.
Band/Mode
Test
Position
CH.
Freq.
(MHz)
Ave.
Power
(dBm)
Power
Drift
(dB)
Tune-
Up Limit
(dBm)
Meas.
SAR
1g
(W/kg)
Scaling
Factor
D.C
Factor
Reporte
d SAR
1g
(W/kg)
2.4GHz/802.11b
Front
06
2437
14.91
0.07
15.0
0.075
1.021
1.02
0.078
27
2.4GHz/802.11b
Back
06
2437
14.91
0.06
15.0
0.130
1.021
1.02
0.135
2.4GHz/802.11b
Left
06
2437
14.91
-0.23
15.0
0.075
1.021
1.02
0.078
2.4GHz/802.11b
Top
06
2437
14.91
-0.10
15.0
0.057
1.021
1.02
0.059
ANSI / IEEE C95.1 – SAFETY LIMIT
Spatial Peak
Uncontrolled Exposure/General Population
1.6 W/kg (mW/g)
Averaged over 1g
Note:
1. Per KDB 447498 D01v06, for each exposure position, if the highest output channel Reported SAR ≤0.8W/kg, other
channels SAR testing is not necessary.
2. Additional WLAN SAR testing was performed for simultaneous transmission analysis.
3. For Hotspot SAR testing, per KDB 941225 D06v02r01, for EUT dimension ≥ 9cm*5cm, the test distance is 10mm. SAR
must be measured for all surfaces and sides with a transmitting antenna located within 2.5cm from that surface or edge.
4. Per KDB 941225 D01v03r01, RMC 12.2kbps setting is used to evaluate SAR. If HSDPA output power is < 0.25dB
higher than RMC 12.2kbps, or Reported SAR with RMC 12.2kbps setting is ≤ 1.2W/kg, HSDPA SAR evaluation can be
excluded.
5. Per KDB 865664 D01v01r04, for each frequency band, repeated SAR measurement is required when the measured
SAR is ≥0.8W/kg.
6. Per KDB 648474 D04v01r03, when the Reported SAR for a body-worn accessory measured without a headset
connected to the handset is ﹥ 1.2 W/kg, SAR testing with a headset connected to the handset is required.
7. Per KDB 941225 D05v02r05, 100% RB allocation SAR measurement is not required when the highest reported SAR
for 1 RB and 50% RB allocation are ≤ 0.8 W/kg. Otherwise, SAR is measured for the highest output power channel.
8. According to KDB 865664 D02v01r02, SAR plot is required for the highest measured SAR in each exposure
configuration, wireless mode and frequency band combination.
9. Highlight part of test data means repeated test.