Instructions / Assembly

ManualsBrandsLogia ManualsGarden Center7-in-1 Wi-Fi Weather Station, Wireless Outdoor Weather Station with Console Monitoring System & Large 10" Color Display

4. Connect the cable of the rechargeable battery pack (included) to the cable located in the battery

compartment.

5. Adjust the connected cables so they t comfortably in the compartment. Then, insert the battery pack

into the compartment.

6. Close and fasten the battery door back on the compartment.

NOTE: The LED light will ash red every 12 seconds.

3.1.1 INSTALL RAIN GAUGE FUNNEL

Install the rain gauge funnel and rotate clockwise to lock the funnel to the sensor array

Rain Collector Installation

1 Align

Lock grooves

2 Lock

3.1.2 INSTALL RECHARGEABLE BATTERIES

Step 1: Unscrew the battery door at bottom of unit and take

out the cable socket.

Step 2: Connect the Ni-MH rechargeable battery plug to the

socket.

Step 3: Make sure the red LED indicator on the back of the

sensor array is turn on and then begin ashing every 12

seconds.

Step 4: Adjust the cable and socket into shallow hole and put

the battery pack into the battery compartment.

3.1.1 INSTALL RAIN GAUGE FUNNEL

Install the rain gauge funnel and rotate clockwise to lock the funnel to the sensor array

Rain Collector Installation

1 Align

Lock grooves

2 Lock

3.1.2 INSTALL RECHARGEABLE BATTERIES

Step 1: Unscrew the battery door at bottom of unit and take

out the cable socket.

Step 2: Connect the Ni-MH rechargeable battery plug to the

socket.

Step 3: Make sure the red LED indicator on the back of the

sensor array is turn on and then begin ashing every 12

seconds.

Step 4: Adjust the cable and socket into shallow hole and put

the battery pack into the battery compartment.

1. Remove the protection lm on the solar cell.

2. Loosen the screw at the joint (if you haven’t already) so the gear on the other side of the joint

pushes out. The solar cell should now be in an unlocked position.

3. Adjust the vertical angle of the solar cell to get the most optimal usage out of the solar cell

depending on your location.

4. Push the gear inward and tighten the screw until the gears lock in place.

Step 5: Close the battery door and tighten the screw

Step 6: Remove the solar panel protection lm.

NOTE:

- USE ONLY the rechargeable 3.6V Ni-MH battery-pack provided.

- Do NOT use battery of different type.

- It is recommendable to wrap water-resistant tape over the socket for extra protection against

moisture and salinity in air.

3.1.3 ADJUST THE SOLAR PANEL

The tilting angle of solar panel can be adjusted vertically from 0° into 15°, 30°, 45° and 60°

positions depending on the area you are living in. For optimal power output year-round, please

set the tilt angle that is closest to your latitude.

E.g.,

Location (latitude, longitude) Solar panel tilt angle

45°

60°

30°

15°

0°

Hamburg (53.558, 9.7874) 60°

Chicago (42.1146, -88.0464) 45°

Houston (29.7711, -95.3552) 30°

Bangkok (14.2752, 100.5684) 15°

Sydney (-33.5738, 151.3053) * 30°

*Sensors installed in Southern Hemisphere must have their solar panels facing North.

Step 1: Loosen the screw lightly until the gears on the

opposite side separated from lock position.

Step 5: Close the battery door and tighten the screw

Step 6: Remove the solar panel protection lm.

NOTE:

- USE ONLY the rechargeable 3.6V Ni-MH battery-pack provided.

- Do NOT use battery of different type.

- It is recommendable to wrap water-resistant tape over the socket for extra protection against

moisture and salinity in air.

3.1.3 ADJUST THE SOLAR PANEL

The tilting angle of solar panel can be adjusted vertically from 0° into 15°, 30°, 45° and 60°

positions depending on the area you are living in. For optimal power output year-round, please

set the tilt angle that is closest to your latitude.

E.g.,

Location (latitude, longitude) Solar panel tilt angle

45°

60°

30°

15°

0°

Hamburg (53.558, 9.7874) 60°

Chicago (42.1146, -88.0464) 45°

Houston (29.7711, -95.3552) 30°

Bangkok (14.2752, 100.5684) 15°

Sydney (-33.5738, 151.3053) * 30°

*Sensors installed in Southern Hemisphere must have their solar panels facing North.

Step 1: Loosen the screw lightly until the gears on the

opposite side separated from lock position.

Step 5: Close the battery door and tighten the screw

Step 6: Remove the solar panel protection lm.

NOTE:

- USE ONLY the rechargeable 3.6V Ni-MH battery-pack provided.

- Do NOT use battery of different type.

- It is recommendable to wrap water-resistant tape over the socket for extra protection against

moisture and salinity in air.

3.1.3 ADJUST THE SOLAR PANEL

The tilting angle of solar panel can be adjusted vertically from 0° into 15°, 30°, 45° and 60°

positions depending on the area you are living in. For optimal power output year-round, please

set the tilt angle that is closest to your latitude.

E.g.,

Location (latitude, longitude) Solar panel tilt angle

45°

60°

30°

15°

0°

Hamburg (53.558, 9.7874) 60°

Chicago (42.1146, -88.0464) 45°

Houston (29.7711, -95.3552) 30°

Bangkok (14.2752, 100.5684) 15°

Sydney (-33.5738, 151.3053) * 30°

*Sensors installed in Southern Hemisphere must have their solar panels facing North.

Step 1: Loosen the screw lightly until the gears on the

opposite side separated from lock position.

Step 2: Adjust the vertical angle of the solar panel (0°,

15°, 30°, 45°, 60°) according to the latitude of your

location.

Step 3: Push the gear and tighten the screw until the

gears are securely locked.

3.1.4 INSTALL MOUNTING POLE

1. Stick the 2 rubber pads (provided) onto the inner sides of the mounting part

2. Insert the 2 screws into the sensor array mounting base and hand tighten the screws

3. Place the sensor array over the mounting pole and align the sensor array to North direction

4. Tighten the screws to t the size of your mounting pole

Add rubber pad

before mounting

on pole

NOTE:

- Any metal object can attract lightning strikes, including your sensor-array mounting pole. Never install

sensor-array in stormy days.

- If you want to install a sensor-array on a house or building, consult a licensed electrical engineer to ensure

proper grounding. Direct lightning impact on a metal pole can damage or destroy your home.

- Installing the sensor at high location may result in personal injury or death. Perform as many initial

inspections and operations as possible on the ground and in buildings or houses. Only install the sensor-

array on clear, dry days.

ADJUSTING THE SOLAR CELL

Step 2: Adjust the vertical angle of the solar panel (0°,

15°, 30°, 45°, 60°) according to the latitude of your

location.

Step 3: Push the gear and tighten the screw until the

gears are securely locked.

3.1.4 INSTALL MOUNTING POLE

1. Stick the 2 rubber pads (provided) onto the inner sides of the mounting part

2. Insert the 2 screws into the sensor array mounting base and hand tighten the screws

3. Place the sensor array over the mounting pole and align the sensor array to North direction

4. Tighten the screws to t the size of your mounting pole

Add rubber pad

before mounting

on pole

NOTE:

- Any metal object can attract lightning strikes, including your sensor-array mounting pole. Never install

sensor-array in stormy days.

- If you want to install a sensor-array on a house or building, consult a licensed electrical engineer to ensure

proper grounding. Direct lightning impact on a metal pole can damage or destroy your home.

- Installing the sensor at high location may result in personal injury or death. Perform as many initial

inspections and operations as possible on the ground and in buildings or houses. Only install the sensor-

array on clear, dry days.