Instructions / Assembly
26
27
NOTE: While in normal mode, press the SET button to switch between year and date display.
During these settings, you can go back to normal mode by press and hold the SET button for
two (2) seconds.
Press and hold the SET button for two (2) seconds to enter the setting mode. Press DOWN/INDEX or UP/
FORECAST button to adjust the setting and press SET button again to save and proceed with next step of
the setting. Refer to the chart below for the order of settings.
The weather console backlight can be adjusted, using the HI/LO/AUTO slider to select the appropriate
brightness:
• Slide to the HI position for the brighter backlight.
• Slide to the LO position for the dimmer backlight.
• Slide to the AUTO position for auto-adjusted backlight.
Use the viewing angle slider to change the viewing angle of the display.
If the console is placed directly on a at surface with the kickstand, move the slider to the table stand
icon position, if the console is hung on the wall with the wall mounting hole, move the slider to wall
mount icon position.
Use the SET UNIT button to change the unit of the readings on the console display.
1. Press and hold the SET UNIT button for two (2) seconds to enter the unit setting mode.
2. Press the SET UNIT button to proceed to the next setting step.
3. Press the UP/FORECAST or DOWN/INDEX button to change the value. Press and hold the button
to change the value quickly.
4. Press and hold SET UNIT button for two (2) seconds to exit the unit setting mode at any time.
TIME, DATE, AND GENERAL SETTINGS DISPLAY BACKLIGHT
SET VIEWING ANGLE
UNIT SETTING
Level Light Moderate Strong Storm
Speed
4.3.7 WATER LEAK (OPTIONAL LEAK SENSOR)
You can add up to 7 additional Water Leak sensors (optional, refer
to section 3.2.1)
The channel number(s) of the corresponding water leak sensor(s)
added to the console will be shown with the NO LEAKING icon.
When water leaking is detected, the channel number of the sensor
NOTE:
When low battery is detected, the channel number of the sensor detecting the low battery
y 4 seconds.
4.3.8 WIND
4.3.8.1 WIND SPEED AND DIRECTION SECTION OVERVIEW
W
Real time wind
direction indicator
Wind direction
ind speed level
indicator
Past wind directions
indicator of last 5
minutes (maximum 6)
2-8 mph
3-13 km/h
9-25 mph
14-41 km/h
25–54 mph
42–57 km/h
≥ 55 mph
≥ 88 km/h
Mode Setting procedure
1 Hour Press [
/ FORECAST ] or [ / INDEX ] key to adjust the hour
2 Minute Press [
/ FORECAST ] or [ / INDEX ] key to adjust the minute
3 12/24 hour format Press [
/ FORECAST ] or [ / INDEX ] key to select 12 or 24 hour format
4 Year Press [
/ FORECAST ] or [ / INDEX ] key to adjust the year
5 Month Press [
/ FORECAST ] or [ / INDEX ] key to adjust the month
6 Day Press [
/ FORECAST ] or [ / INDEX ] key to adjust the day
7 M-D/D-M format Press [
/ FORECAST ] or [ / INDEX ] key to select "Month /
Day" or "Day / Month" display format
8 Select Sunrise /
Sunset or Moon rise
/ Moon set display
Press [
/ FORECAST ] or [ / INDEX ] key to select Sunrise /
Sunset or Moon rise / Moon set display
9 Time Sync ON/OFF Press [
/ FORECAST ] or [ / INDEX ] key to enable or disable
Time Sync function.
If you want to set the time manually, you should set Time Sync OFF
10 Weekday language Press [
/ FORECAST ] or key to select weekday display language[ / INDEX ]
Mode Setting procedure
1 Temperature unit Press [ / FORECAST ] or [ / INDEX ] key to select °C or °F
2 Rain unit Press [ / FORECAST ] or [ / INDEX ] key to select mm or in
3 Wind speed unit Press [ / FORECAST ] or [ / INDEX ] key to select m/s, km/h, knots or mph
4 Distance unit Press [ / FORECAST ] or [ / INDEX ] key to select k/m or mi (miles)
4 Baro pressure unit Press [ / FORECAST ] or [ / INDEX ] key to select hPa, inHg or mmHg
5 Light intensity Press [ / FORECAST ] or [ / INDEX ] key to select Klux, Kfc or W/m
2
26
4 Distance unit Press [ / FORECAST ] or [ / INDEX ] key to select k/m or mi (miles)
5 Baro pressure
unit
Press [ / FORECAST ] or [ / INDEX ] key to select hPa, inHg or
mmHg
6 Light intensity Press [ / FORECAST ] or [ / INDEX ] key to select Klux, Kfc or W/m
2
4.4.3 BACK LIGHT
The main unit back light can be adjust, using the [ HI / LO / AUTO ] sliding switch to select the
appropriate brightness:
- Slide to the [ HI ] position for the brighter back light.
- Slide to the [ LO ] position for the dimmer back light.
- Slide to the [ AUTO ] position for the auto adjust back light that according to environment light level
4.4.4 SET VIEWING ANGLE OF THE DISPLAY
User can use the [ Viewing angle ] slide switch to set the
viewing angle:
If the clock is placed directly on a at surface with the table
stand, slide the switch to table stand icon position, if the
clock is hanged on the wall with the wall mounting hole,
slide the switch to wall mount icon position.
Table stand Wall mount
5. CREATE PWL ACCOUNT & SETUP WI-FI CONNECTION OF CONSOLE
The console can upload /download weather data in ProWeatherLive (PWL) cloud server through
WI-FI router, you can follow the step below to setup your device.
NOTE:
ProWeatherLive (PWL) website and APP are subjected to change without notice.
5.1 CREATE PWL ACCOUNT AND ADD NEW DEVICE IN PWL
1. In https://proweatherlive.net click the "Create Your Account" then follow the instructions to
create your account.
create your account.
2. Log in the ProWeatherLive and then click the "Edit Devices" in the pull down menu.
Account
Edit Devices
Dashboard
Unit & Display
Alert Setting
Help
FAQ
Weather Server
Data Export
Log Out
CREATE PWL ACCOUNT & SET UP WI-FI
®
CONNECTION
The console can upload/download weather data in ProWeatherLive (PWL) cloud server through wi-
router, follow the step below to set up your device.
PAIRING THE SENSOR(S) MANUALLY
Whenever you change the batteries of the 7-in-1 weather sensor or other additional sensors,
re-synchronization must be done manually.
1. Change all the batteries to new ones in the low battery sensor(s).
2. Press the SENSOR/WI-FI button on the console to enter sensor synchronization mode (as
indicated by the ashing antenna).