Installation Guide
25
Viewing Outdoor Channels
Receiving Wireless Sensor Signals
This console is capable of pairing with the wireless weather sensor and up to seven (7) additional
wireless hygro-thermo sensors. If you have two (2) or more sensors installed, press the CH button to
cycle between dierent wireless channels in normal operating mode, or press and hold the CH button
for two (2) seconds to toggle auto-cycle mode on, which cycles through displaying all connected
channels at 4-second intervals. While the console is in auto-cycle mode, you can press the CH button
once to toggle auto-cycle mode o and continue displaying the current channel.
1. While in normal operating mode, press the WI-FI/SENSOR button once to start receiving the
current sensor signal on the channel being displayed. (i.e. if you’re on CH 1 and press the WI-FI/
SENSOR button, the current wireless sensor signal being received will only display on CH 1.) The
signal icon will start ashing.
2. The signal icon will continue ashing until it successfully receives a signal. If no signal is
received within ve (5) minutes, the icon will disappear.
3. If the signal for the outdoor channel has been interrupted and does not recover within 15
minutes, the signal icon will disappear. The temperature and humidity section (outdoor) will
display “—” on the corresponding channel.
4. If the signal still does not recover within 48 hours, the “—” display will become permanent.
You will need to replace the batteries on the associated channel’s sensor and press the WI-FI/
SENSOR button to pair up the sensors again.
5. After replacing batteries in the display console or the wireless weather sensor, or if the unit fails
to receive a specied channel, press the WI-FI/SENSOR button while the failed channel is being
displayed to manually receive that sensor’s signal again.
Indoor Comfort Indicator Key
The indoor comfort indicators display a pictorial representation based on the indoor air temperature
and humidity levels to determine the approximate comfort level.
Northern Hemisphere Icons Southern Hemisphere IconsMoon Phase
New Moon
Waxing Crescent Moon
First Quarter Moon
Waxing Gibbous Moon
Full Moon
Waning Gibbous Moon
Third Quarter Moon
Waning Crescent Moon
NOTE:
- In alarm mode, the “
” icon will display on the LCD.
Alarm o Alarm on Alarm with ice-alert
Temp/Humidity Trend
Arrow Icon
Rising Steady Falling
Too cold Comfortable Too hot
No signal Weak signal Good signal
16
ACTIVATING ALARM AND TEMPERATURE PRE-ALARM FUNCTION
1. In normal mode, press [ ALARM ] key to show the alarm time for 5 seconds.
2. When the alarm time displays, press [ ALARM ] key again to activate the alarm function.
Or press [ ALARM ] key twice to activate the alarm with ice pre-alarm function.
Alarm off Alarm on Alarm with ice-alert
NOTE:
minutes earlier if the outdoor temperature is below -3°C.
When clock reach the alarm time, alarm sound will start.
Where it can be stopped by following operation:
- Auto-stop after 2 minutes alarming if without any operation and the alarm will activate again in
the next day.
- By pressing [ALARM / SNOOZE] key to enter snooze that the alarm will sound again after 5
minutes.
- By pressing and hold [ALARM / SNOOZE] key for 2 seconds to stop the alarm and will
activate again in the next day
- By pressing [ ALARM ] key to stop the alarm and the alarm will activate again in the next day.
NOTE:
- The snooze could be used continuously in 24 hours.
- During the snooze, the alarm icon “
TEMPERATURE / HUMIDITY FUNCTION
- The temperature and humidity reading are display on the outdoor and indoor (CH) section.
- Use the [ °C / °F ] slide switch to select the temperature display unit.
- If temperature / humidity is below the measurement range, the reading will show “Lo”. If
temperature / humidity is above the measurement range, the reading will show “HI”.
COMFORT INDICATION
The comfort indication is a pictorial indication
based on indoor air temperature and humidity in
an attempt to determine comfort level.
Too cold Comfortable Too hot
NOTE:
- Comfort indication can vary under the same temperature, depending on the humidity.
- There is no comfort indication when temperature is below 0°C (32°F) or over 60°C (140°F).
WIRELESS SENSOR SIGNAL RECEIVING
1. The console display signal strength for the wireless sensor(s), as per table below:
OUTDOOR 7-IN-1 SENSOR
INDOOR CHANNEL SENSOR
No signal Weak signal Good signal
2. If the signal has discontinued and does not recover within 15 minutes, the signal icon will
disappear. The temperature and humidity will display “Er” for the corresponding channel.
3. If the signal does not recover within 48 hours, the “Er” display will become permanent. You
need to replace the batteries and then press [ SENSOR / WI-FI] key to pair up the sensor
again.
SETUP page