Installation Guide

10
SETTING UP RAIN COLLECTOR
INSTALLING THE BATTERIES
MOUNTING SENSOR ON POLE
1. Align the notches on the funnel with the lock grooves inside the rain collector.
2. Insert the funnel in the rain collector and screw on tight to lock it in place.
1. Unscrew the battery door at the bottom of the 7-in-1 outdoor sensor.
2. Insert three (3) AA batteries (not included) according to the +/- polarity labeled in the compartment.
3. Screw the battery door back onto the compartment.
NOTE: The LED light will ash red every 12 seconds.
1. Pick a location for the 7-in-1 outdoor sensor that is open with no obstructions.
2. Set the sensor so the rain collector faces north and UV/light sensor faces south.
3. Secure the sensor onto a mounting post or pole (not included) using the mounting clamp (included).
4. Add rubber pads onto mounting clamp before fastening the mounting clamp on the sensor.
5. Tighten the mounting clamp using included screws onto the bottom of the sensor once it is on a pole.
NOTE: Place sensor on a steel pole or post with a 1.4″ – 1.6″ (35 – 40 mm) diameter and is a
minimum of 6.6 ft. (2 m) o the ground.
4
INSTALLATION AND SETUP
Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 wireless indoor
sensors. (1pc wireless indoor sensor included)
INSTALL WIRELESS 7-IN-1 SENSOR
Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity,
temperature and humidity for you. It’s assembled and calibrated for your easy installation.
INSTALL RAIN COLLECTOR
Rain Collector Installation
1 Align
Lock grooves
2 Lock
INSTALL BATTERIES
Unscrew the battery door at bottom of unit and insert the batteries
according to the +/- polarity indicated. Screw the battery door
compartment on tightly.
NOTE:
The red LED will begin ashing every 12 seconds.
Screw
location
3 x AA
batteries
MOUNTING POLE AND DIRECTION ALIGNMENT
Install the wireless 7-IN-1 sensor in an open
location with no obstructions above and around the
sensor for accurate rain and wind measurement.
Install the sensor with the smaller end facing the
North to properly orient the wind direction vane.
Secure the mounting stand and bracket (included)
to a 35 ~ 40mm diameter steel post or pole, and
allow minimum 2m off the ground.
Point to
SOUTH
Point to
NORTH
2 meter
off the
ground
mounting pole
and stand not
included
Add rubber
pad before
mounting on
pole or post
4
INSTALLATION AND SETUP
Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 wireless indoor
sensors. (1pc wireless indoor sensor included)
INSTALL WIRELESS 7-IN-1 SENSOR
Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity,
temperature and humidity for you. It’s assembled and calibrated for your easy installation.
INSTALL RAIN COLLECTOR
Rain Collector Installation
1 Align
Lock grooves
2 Lock
INSTALL BATTERIES
Unscrew the battery door at bottom of unit and insert the batteries
according to the +/- polarity indicated. Screw the battery door
compartment on tightly.
NOTE:
The red LED will begin ashing every 12 seconds.
Screw
location
3 x AA
batteries
MOUNTING POLE AND DIRECTION ALIGNMENT
Install the wireless 7-IN-1 sensor in an open
location with no obstructions above and around the
sensor for accurate rain and wind measurement.
Install the sensor with the smaller end facing the
North to properly orient the wind direction vane.
Secure the mounting stand and bracket (included)
to a 35 ~ 40mm diameter steel post or pole, and
allow minimum 2m off the ground.
Point to
SOUTH
Point to
NORTH
2 meter
off the
ground
mounting pole
and stand not
included
Add rubber
pad before
mounting on
pole or post
1
2