Installation Guide

ManualsBrandsLogia ManualsGarden Center5-in-1 Indoor/Outdoor Wi-Fi Weather Station with Remote Monitoring System

MOUNT THE SENSOR OUTDOORS

If securing to a railing, make sure the railing is made of suitable material, and screw directly through

the openings in the base stand into the railing until secure.

1. The wireless weather sensor should be mounted in an open area with no obstructions above and/

or around it, so that it can accurately measure the rain and wind.

2. The wind vane should be pointed due North (refer to the arrow on top of the unit) in order to be

properly oriented and receive accurate wind readings.

3. The mounting stand and included clamps should be secured to a post or pole, with a minimum of

4.9 ft. (1.5 m) ground clearance.

4. If securing to a pole, make sure you add the rubber pads to the clamp before fastening it with the

included screws. The pole should be between 1″-1.3″ in diameter.

4. Insert the nut into the hexagonal hole on the side of the stand and hold it in place, then insert the

screw through the other side. Use a screwdriver to tighten the screw.

Step 4

Place the nut in the hexagon hole of the stand,

then insert the screw in other side and then

tighten it by the screw driver.

Install the wireless 5-IN-1 sensor

in an open location with no

obstructions above and around

the sensor for accurate rain

and wind measurement. Install

the sensor with the smaller end

facing the North to properly orient

the wind direction vane.

Secure the mounting stand and

clamps (included) to a post or

pole, and allow minimum 1.5m

off the ground.

1.5 meter off

the ground

Add rubber

pads before

mount on

the pole

Point to

NORTH

MOUNTING GUIDELINES

1. Install the wireless 5-IN-1 sensor at least 1.5m off the ground for better and more accurate

wind measurements.

2. Choose an open area within 150 meters from the LCD console.

3. Install the wireless 5-IN-1 sensor as level as possible to achieve accurate rain and wind

measurements.

4. Mount the wireless 5-IN-1 sensor with the wind meter end pointing to the North to correctly

orient direction of the wind vane.

A. Mounting on pole (Pole Diameter 1"~1.3")

(25~33mm)

B. Mounting on the railing

Install the wireless 5-IN-1 sensor in an

open location with no obstructions above

and around the sensor for accurate

rain and wind measurement. Install

the sensor with the smaller end facing

the North to properly orient the wind

direction vane.

Secure the mounting stand and bracket

(included) to a post or pole, and allow

minimum 1.5m off the ground.

1.5 meter off

the ground

Add rubber

pads before

mount on

the pole

Point to

NORTH

POWER UP CONSOLE

Your console can pairing up with the wireless 5-IN-1 outdoor weather sensor and up to 7

optional wireless sensors. (Not included)

INSTALL THE BACKUP BATTERY

1. Remove the battery door of the console.

2. Insert a new button cell battery.

3. Replace the battery door.

NOTE:

The backup battery can backup: Time & Date, Max/Min & Past 24 hours weather records, Alert

setting values, offset value of weather data and Sensor(s) channel history.

The built-in memory can backup: Router setting and Weather server setting

POWER UP THE CONSOLE

1. Plug the power adaptor to power up the console.

2. Once the console power up, all the segments of the LCD will be shown.

3. The console will automatically start AP mode.

NOTE:

If no display appears on the LCD after you plug the adaptor, press [ RESET ] key by using a

pointed object.

SET LCD DISPLAY VIEWING ANGLE

Press [ ] or [ ] key in normal mode to adjust LCD viewing angle to t table stand or wall

mount situation.

MOUNTING ON POLE

(POLE DIAMETER 1”-1.3”)

(25-33MM)

Point to NORTH

Add rubber

pads before

mount on

the pole

1.5 meter off the

ground