Warranty

ManualsBrandsLogia ManualsGarden Center5-in-1 Indoor/Outdoor Weather Station Remote Monitoring System with PC Connect

PAIRING THE WIRELESS WEATHER SENSOR WITH THE DISPLAY CONSOLE

CHANGING BATTERIES AND MANUAL PAIRING

PAIRING ADDITIONAL WIRELESS SENSORS WITH THE DISPLAY CONSOLE

SYNC PC TIME

MANUALLY SETTING THE TIME

NOTE: The display console does not need to be plugged in, and is rated to last up to 2 years on

battery power alone. However, it can also be powered via the micro USB connection.

NOTE: Any time you press the RESET key underneath the wireless weather sensor, it generates a new

ID code for pairing with the console, and you will need to press the SENSOR/SYNC button on the

console for the two devices to pair again.

Whenever you change the batteries in the console, you will need to manually re-pair it with the

wireless weather sensor. Follow these instructions to manually pair your console with the sensor.

The display console should automatically search and pair with any additional wireless hygro-thermo

outdoor sensors you install. You can also press the SENSOR/SYNC button to search manually for the

sensor while on the channel where it should display. Once your sensor has paired, the sensor signal

strength indicator and weather information will appear in the temperature and humidity (outdoor)

section when you are on the channel associated with that sensor.

The display console is designed to automatically synchronize its calendar and clock when connected

to your computer via a micro USB data cable, as long as you have the PC Software, “Weather Tool,”

running. (Software can be downloaded online from our website: http://www.www.logiaweatherstation.

com). Once you connect the display console to the computer, it will automatically synchronize the

time*, and will re-sync again at 12:00AM each day. You can also press the TIME SYNC button at the

rear of the console to sync the time with your PC.

*Time synchronization can sometimes take up to 30 minutes.

NOTES:

• The time sync function will only work with the “Weather Tool” PC Software installed, so make sure

that software is open and running when you connect the console.

• The time will sync to the time on your PC, so make sure that your PC time is correct before

connecting the unit. Once PC time has synced, the icon will appear in the TIME section of

the LCD Display.

• If you want to disable the automatic time sync function, press and hold the TIME SYNC button for

eight (8) seconds. Repeat this process to re-enable it.

1. Once you insert the batteries and the display console powers on, it should automatically search

for and connect to the wireless weather sensor. If the console does not connect within the rst 15

minutes, refer to the following section, Changing Batteries and Manual Pairing, for instructions on

manual pairing.

2. You will see the icon of an antenna blinking in the temperature and humidity (outdoor) section of

the display.

3. Once the pairing process completes, the antenna icon will appear solid (not blinking), and the

readings for outdoor temperature and humidity, wind speed, wind direction, and rainfall will

appear in their designated sections of the LCD display.

1. Press the CH button until the antenna icon appears in the temperature and humidity

(outdoor) section of the LCD display.

2. Press the SENSOR/SYNC button at the back of the console.

3. Go outside to where your wireless weather sensor is mounted, and press the RESET key on its

underside. Make sure after pressing the RESET key that the red LED indicator is ashing every 12

seconds.

1. In normal operating mode, press and hold the CLOCK SET button for two (2) seconds to enter the

clock setting menu.

2. Press the or buttons to adjust the hour.

3. Press the CLOCK SET button again to make adjustments to the next setting.

4. Settings cycle through the following options: HOUR > MINUTE > SECOND > 12-hour/24-hour format

> Year > Month > Day > M-D/D-M date format > Longitude (for sunrise/sunset) > Latitude (for

sunrise/sunset) > Time Zone > Language

5. Press the CLOCK SET button one nal time after adjusting all settings options to save and exit, or the

console will automatically save and exit the menu after 60 seconds of idle time.

4. Once the batteries are inserted, the LCD display should power on.

NOTE: If nothing appears on the LCD display after you insert the batteries, use a pin or similar

small object to press the RESET button at the rear.

MAIN CONSOLE

Your main console can pairing up with the wireless 5-in-1 outdoor weather sensor and up to 7

optional wireless hygro-thermo outdoor sensors. (Not included)

Powering up the main console

1. Remove the battery door on the back side of the main unit.

2. Insert 6 new AA batteries and replace the battery door.

3. Once the batteries are inserted, the segments of the LCD will be shown.

NOTE:

If no display appears on the LCD after inserting the batteries, press [ RESET ] key by using a

pointed object.

Pairing of wireless 5-in-1 weather sensor with main console

After insertion of batteries, the main console will automatically search and connect the

wireless 5-in-1 sensor (antenna blinking). Once the connection is successful, antenna mark

and readings for outdoor temperature & humidity, wind speed, wind direction and rainfall will

appear on the display.

Changing batteries and manual pairing of sensor

Whenever you changed the batteries of the wireless 5-in-1 sensor, pairing must be done

manually.

1. Change all the batteries to new ones in the sensor.

2. Press [ CH ] until the

icon appear in the Outdoor section

3. Press [ SENSOR / SYNC ] key.

4. Press [ RESET ] key on the sensor.

NOTE:

Pressing [ RESET ] key at bottom of wireless 5-in-1 sensor will generate a new ID code for

pairing purpose. So you also need to press the [ SENSOR / SYNC ] key on the console to

repairing up the sensor.

Pairing the wireless sensor(s) with the console

The console will automatically search and pair up your wireless sensor(s). You can also press

[SENSOR / SYNC ] key to search the on display channel's sensor manually. Once your sensor

paired up, the sensor signal strength indicator and weather information will appear on your

console display.

SYNC UP PC TIME

This unit is designed to automatically synchronize its calendar and clock when connected to

the computer with PC software "Weather Tool" through USB data cable. Once connected to the

computer, the unit will automatically synchronize the time instantly and 12:00am per day. You

can also press the [ TIME SYNC ] key to sync up PC time instantly.

NOTE:

- The time sync function only work with the PC software "Weather Tool", please make sure the

PC software is open.

- PC Time sync up is according to your current PC time, so please ensure your PC time is

correct. Once the PC time sync up the

icon will appear in the Time section.

- You can also enable or disable auto time sync function by press and hold [ TIME SYNC ] key

for 8 seconds.

MAIN CONSOLE

Your main console can pairing up with the wireless 5-in-1 outdoor weather sensor and up to 7

optional wireless hygro-thermo outdoor sensors. (Not included)

Powering up the main console

1. Remove the battery door on the back side of the main unit.

2. Insert 6 new AA batteries and replace the battery door.

3. Once the batteries are inserted, the segments of the LCD will be shown.

NOTE:

If no display appears on the LCD after inserting the batteries, press [ RESET ] key by using a

pointed object.

Pairing of wireless 5-in-1 weather sensor with main console

After insertion of batteries, the main console will automatically search and connect the

wireless 5-in-1 sensor (antenna blinking). Once the connection is successful, antenna mark

and readings for outdoor temperature & humidity, wind speed, wind direction and rainfall will

appear on the display.

Changing batteries and manual pairing of sensor

Whenever you changed the batteries of the wireless 5-in-1 sensor, pairing must be done

manually.

1. Change all the batteries to new ones in the sensor.

2. Press [ CH ] until the

icon appear in the Outdoor section

3. Press [ SENSOR / SYNC ] key.

4. Press [ RESET ] key on the sensor.

NOTE:

Pressing [ RESET ] key at bottom of wireless 5-in-1 sensor will generate a new ID code for

pairing purpose. So you also need to press the [ SENSOR / SYNC ] key on the console to

repairing up the sensor.

Pairing the wireless sensor(s) with the console

The console will automatically search and pair up your wireless sensor(s). You can also press

[SENSOR / SYNC ] key to search the on display channel's sensor manually. Once your sensor

paired up, the sensor signal strength indicator and weather information will appear on your

console display.

SYNC UP PC TIME

This unit is designed to automatically synchronize its calendar and clock when connected to

the computer with PC software "Weather Tool" through USB data cable. Once connected to the

computer, the unit will automatically synchronize the time instantly and 12:00am per day. You

can also press the [ TIME SYNC ] key to sync up PC time instantly.

NOTE:

- The time sync function only work with the PC software "Weather Tool", please make sure the

PC software is open.

- PC Time sync up is according to your current PC time, so please ensure your PC time is

correct. Once the PC time sync up the

icon will appear in the Time section.

- You can also enable or disable auto time sync function by press and hold [ TIME SYNC ] key

for 8 seconds.