Warranty

12
13
MOUNT THE SENSOR OUTDOORS
INSTALLING BATTERIES
Please note that there are two dierent ways you can attach the pole to the base, depending on
how you will be mounting it outdoors. If you will be fastening the sensor directly to a railing, use the
option that positions the stand perpendicular to the sensor pole. If you will be fastening it to a pole,
use the slot that positions the base parallel to the sensor pole.
If securing to a railing, make sure the railing is made of suitable material, and screw directly through
the openings in the base stand into the railing until secure.
Your display console can pair with the wireless weather sensor as well as up to seven (7) optional
wireless hygro-thermo outdoor sensors (not included).
1. The wireless weather sensor should be mounted in an open area with no obstructions above and/
or around it, so that it can accurately measure the rain and wind.
2. The wind vane should be pointed due North (refer to the arrow on top of the unit) in order to be
properly oriented and receive accurate wind readings.
3. The mounting stand and included clamps should be secured to a post or pole, with a minimum of
4.9 ft. (1.5 m) ground clearance.
4. If securing to a pole, make sure you add the rubber pads to the clamp before fastening it with the
included screws. The pole should be between 1″-1.3″ in diameter.
4. Insert the nut into the hexagonal hole on the side of the stand and hold it in place, then insert the
screw through the other side. Use a screwdriver to tighten the screw.
5. The mounting location should be within 492 ft. (150 m) of the location where you will be keeping
the display console with few obstructions and relatively clear sightlines. If there are multiple walls/
levels/buildings in between the sensor and the display console, the functionality could be
compromised and you will need less space between the two.
6. Use the built-in level to make sure the sensor is parallel with the ground.
1. Remove the battery door on the rear of the console unit.
2. Insert six (6) new AA batteries, making sure the polarities match up with the polarities marked
inside the compartment.
3. Replace the battery door.
DISPLAY CONSOLE SETUP
5
Step 4
Place the nut in the hexagon hole of the stand,
then insert the screw in other side and then
tighten it by the screw driver.
Install the wireless 5-IN-1 sensor
in an open location with no
obstructions above and around
the sensor for accurate rain
and wind measurement. Install
the sensor with the smaller end
facing the North to properly orient
the wind direction vane.
Secure the mounting stand and
clamps (included) to a post or
pole, and allow minimum 1.5m
off the ground.
1.5 meter off
the ground
Add rubber
pads before
mount on
the pole
Point to
NORTH
MOUNTING GUIDELINES
1. Install the wireless 5-IN-1 sensor at least 1.5m off the ground for better and more accurate
wind measurements.
2. Choose an open area within 150 meters from the LCD console.
3. Install the wireless 5-IN-1 sensor as level as possible to achieve accurate rain and wind
measurements.
4. Mount the wireless 5-IN-1 sensor with the wind meter end pointing to the North to correctly
orient direction of the wind vane.
A. Mounting on pole (Pole Diameter 1"~1.3")
(25~33mm)
B. Mounting on the railing
5
Step 4
Place the nut in the hexagon hole of the stand,
then insert the screw in other side and then
tighten it by the screw driver.
Install the wireless 5-IN-1 sensor
in an open location with no
obstructions above and around
the sensor for accurate rain
and wind measurement. Install
the sensor with the smaller end
facing the North to properly orient
the wind direction vane.
Secure the mounting stand and
clamps (included) to a post or
pole, and allow minimum 1.5m
off the ground.
1.5 meter off
the ground
Add rubber
pads before
mount on
the pole
Point to
NORTH
MOUNTING GUIDELINES
1. Install the wireless 5-IN-1 sensor at least 1.5m off the ground for better and more accurate
wind measurements.
2. Choose an open area within 150 meters from the LCD console.
3. Install the wireless 5-IN-1 sensor as level as possible to achieve accurate rain and wind
measurements.
4. Mount the wireless 5-IN-1 sensor with the wind meter end pointing to the North to correctly
orient direction of the wind vane.
A. Mounting on pole (Pole Diameter 1"~1.3")
(25~33mm)
B. Mounting on the railing
5
Step 4
Place the nut in the hexagon hole of the stand,
then insert the screw in other side and then
tighten it by the screw driver.
Install the wireless 5-IN-1 sensor
in an open location with no
obstructions above and around
the sensor for accurate rain
and wind measurement. Install
the sensor with the smaller end
facing the North to properly orient
the wind direction vane.
Secure the mounting stand and
clamps (included) to a post or
pole, and allow minimum 1.5m
off the ground.
1.5 meter off
the ground
Add rubber
pads before
mount on
the pole
Point to
NORTH
MOUNTING GUIDELINES
1. Install the wireless 5-IN-1 sensor at least 1.5m off the ground for better and more accurate
wind measurements.
2. Choose an open area within 150 meters from the LCD console.
3. Install the wireless 5-IN-1 sensor as level as possible to achieve accurate rain and wind
measurements.
4. Mount the wireless 5-IN-1 sensor with the wind meter end pointing to the North to correctly
orient direction of the wind vane.
A. Mounting on pole (Pole Diameter 1"~1.3")
(25~33mm)
B. Mounting on the railing
A
B
MOUNTING ON POLE
(POLE DIAMETER 1”-1.3”)
(25-33MM)
MOUNTING ON A RAILING