Manual

ManualsBrandsLodar ManualsRadio2 Function Receiver/Actuator 12 Volt



ActusManufacturing www.actusinc.com +1651‐487‐8716

240ArlingtonAveEast sales@actusinc.com

St.Paul,MN55117www.actusinc.com



Aach the pivot rod mounng ears

Drilltwoholesperpivotrodmounngearandusetheincluded7/16carriagebolts,lockwasher

andnuttoaachtheearstothecontrolstaonsidewall.





Aach the clevis to the Actuator

Threadtheincluded7/16jamnutfollowedbytheclevisontotheoutputrodoftheactuator.Securethejamnutagainstthebase

oftheclevis.

IMPORTANT—whenthreadingtheclevis,donotallowtheoutputrodoftheactuatortorotate.Rotaonoftheoutputrod

can

damageinternalactuatorcomponents.





Install the electric actuator(s)

Slidethepivotrodthroughtheoneofthepivotrodmounngears,thenthrough

thepivotmountholeontheactuator.Notetheactuatororientaon,the

actuatorcableshouldbeontheboomoftheactuator.Usetheplascspacers

tocentertheactuatorbelow

thevalvecontrolrodyouareconnecngto.Side

therodthroughtheothermounngearandsecureusingtheretainingrings.

NOTE:Dependingonthenumberofactuatorsandthewidthofyourvehicles

controlstaon,youmayneedtocutsomeofthespacersto

allowforproperﬁng.





Before you start

Toinstalltheactuatoryouwillneed17inchesofclearspaceontheboomsideofthecontrolstaon.Werecommendmounng

theactuatorwherethepivotpointisclosesttothecenterofthetruckandonthepassengersideofthevehicle.





Locate the pivot rod mounng ears

Looselyassemblethepivotrodandearsusingtheretainingrings.Placethemunderthecon‐

trolstaonsothepivotrodhas2inchesofspacebetweenitandthevalvelevercontrolrods.

Markthelocaonoftheearholes.



InstallaonInstrucons

8678v01

999‐0805

Summary of content (4 pages)

PAGE 1
Installa on Instruc ons 8678v01 999‐0805 Before you start To install the actuator you will need 17 inches of clear space on the bo om side of the control sta on. We recommend moun ng the actuator where the pivot point is closest to the center of the truck and on the passenger side of the vehicle. Locate the pivot rod moun ng ears Loosely assemble the pivot rod and ears using the retaining rings.
PAGE 2
Locate and loosely a ach the C‐bracket to the control rod From the edge of the pivot rod, measure a distance of 13 7/8 inches towards the outside of the truck. This is where the back of the C‐bracket will be. With the C‐bracket opening facing the pivot rod, loosely mount the C‐ bracket to the control rod using the enclosed U‐bolts, split lock washers and nuts. The C‐bracket should be poin ng straight down. A ach the actuator to the C‐bracket On the actuator clevis, unclasp the clevis pin and pull the pin.
PAGE 3
Troubleshoo ng the Actus Electric Actuator The Actus electric actuator and Lodar controller have no serviceable parts inside. Do not disassemble! Please follow the steps be‐ low to troubleshoot your Actus actuator. If any of the tests fail, contact your local dealer/distributor for addi onal troubleshoo ng informa on or replacement parts. 1.
PAGE 4
ACTUS MANUFACTURING WARRANTY STATEMENT Actus Manufacturing, Inc. (hereinafter referred to as Actus) warrants that the product will be free from defects in material and workmanship for a period of two (2) years from date of shipment, subject to the conditions and restrictions contained herein. Actus further warrants all parts furnished under this warranty for a period which expires upon the termination of the warranty for the product on to which these parts are installed.