Technical Specifications
LOCTITE® Extreme Glue
Page 2 of 4
Revision: June 1, 2020
Supersedes: NEW
Ref. #: 677646
Technical Data Sheet
DIRECTIONS
Typical Application Properties:
Application Temperature:
Apply between 41°F (5°C) to 104°F (40°C)
Odor:
Minimal
Clamp Time:
30 minutes*
Open Time:
8 – 15 minutes*
Full Cure Time:
Approximately 24 hours*
Repositioning Time
5 minutes*
*Time is dependent on temperature, humidity and thickness of adhesive
applied
Typical Cured Performance Properties:
Color:
Clear and Colorless
Water Resistant:
Yes
Shelf Life:
18 Months from date of manufacture unopened
Paintable:
Yes (See page 3 for details)
Lot Code:
(stamped on bottom of
bottle)
YYDDD
YY – Last two digits of year manufactured
DDD – Date of manufacture based on 365 days
of the year
Example: 20125 (May 4, 2020)
Service
Temperature:
- 40°F (-40°C) to 176°F (80°C)
Note: Exposure to temperatures above 122°F
(50°C) will cause yellowing.
Cured Form
Non-flammable, flexible solid
Tensile Shear Strength: 1-inch overlaps cured for 7 days at 73°F (23°C)
Pine to Pine
392 psi
Maple to PVC (hard)
281 psi
Maple to Maple
493 psi
PVC to PVC (hard)
109 psi
Maple to Aluminum
375 psi
Maple to Polycarbonate
473 psi
Aluminum to Aluminum
243 psi
Maple to Acrylic (sanded)
234 psi
Cold rolled steel to itself
189 psi
Maple to ABS
119 psi
Maple to Stainless steel
491 psi
Maple to ABS (sanded)
371 psi
Stainless steel to itself
496 psi
Maple to Fiberglass (sanded)
450 psi
Canvas to Canvas
4 lbs./inch
Felt to Pine
9 lbs./inch
Canvas to Pine
11 lbs./inch
Leather (unfinished) to Pine
8 lbs./inch
Corduroy to Maple
6 lbs./inch
Tensile Shear Strength: 1-inch overlaps cured for 7 days at 73°F (23°C) then 3-hour water immersion
Maple to Maple
471 psi
Maple to Aluminum
370 psi
Compression Shear Strength – Cured for 7 days
Maple to Maple
466 psi
Tools Typically Required:
Wear gloves and wash hands after use.
Safety Precautions:
Use in a well-ventilated area. Protect work area before and during use. Wear gloves (nitrile gloves recommended) and wash hands after use.
Preparation:
Protect work area. Surfaces to be glued must be sound, clean, dry (see Application below) and free of grease, dust, old adhesive residue, paint
and other contaminants such as plasticizers and mold release agents. Remove contaminants with alcohol or acetone (tests surfaces for
compatibility before). For improved adhesion, lightly sand very smooth or glossy surfaces and clean thoroughly. Pre-fit all materials before applying
adhesive. When bonding two non-porous surfaces, dampen surfaces lightly before applying adhesive. Mask off the adjacent areas with tape
before gluing if necessary. To open, rotate cap counterclockwise.
Application:
Apply a thin layer of adhesive to one surface. Bond parts immediately after applying the adhesive and hold or clamp parts together (before skin
formation) for at least 30 minutes. For best results allow 24 hours cure before subjecting to stress. Unlike other adhesives, high pressure during
curing is not necessary. Very porous materials will require a thicker layer of adhesive and application to both surfaces may be required.
TECHNICAL DATA