Technical Specifications


Loctite® 2 in 1™ Seal & Bond
Tub & Tile
Page 3 of 4
Typical Cured
Performance Properties:
Cured Form: Non-flammable solid
Service Temperature: 20°F (-7°C) to 170°F (77°C)
Water Resistant: Yes. Wait until sealant is fully cured before exposing to water (24 to 48 hours)
Paintable: Yes, after 2 hours with latex or oil-based paint
Hardness: 64 Shore A
Elongation: 580% ASTM D 412
Tensile Strength: 2.11 N/mm² (306 psi) ASTM D 412
Extension Recovery: 100% ASTM C 736
Peel Adhesion:
Aluminum Dry:
Glass Dry:
Wood Dry:
Vinyl Dry:
Aluminum Wet:
Vinyl Wet:
2.1 N/mm (12 pli)
1.8 N/mm (10 pli)
7.9 N/mm (45 pli)
2.3 N/mm (13 pli)
1.8 N/mm (10 pli)
3.3 N/mm (19 pli)
ASTM C 794




Directions:
Tools Typically Required:
Utility knife, caulking gun, masking tape and tooling device.
Safety Precautions:
Apply and cure in a well-ventilated area. Wear gloves and wash hands after use.
Preparation:
Apply sealant between 40°F (5°C) and 100°F (38°C). Surfaces must be clean, dry and free of old caulk, grease, dust and other
contaminants. Remove mold or mildew using bleach and detergent that does not contain ammonia. Rinse surface and allow
to dry. For neat bead lines, mask both sides of the joint. Cut the tip off the cartridge or squeeze tube at a 45° angle to desired
bead size (minimum of 3 mm or 1/8”).
Application:
Using a caulking gun, apply sealant with steady pressure, forcing the sealant into the joint. Smooth bead immediately with a
wet finger or a tool. Remove masking tape immediately after tooling and wipe excess off of hands and tools. Sealant is
paintable with a latex or oil-based paint after 2 hours. Wait 24 to 48 hours before exposing to water. Note: Clear sealant will
extrude white and then turn to clear as it cures.
Clean-up:
Clean tools and uncured product residue immediately with warm, soapy water. Cured sealant may be carefully cut away with a
sharp-edged tool.
Storage & Disposal:
PROTECT FROM FREEZING. To maximize shelf life, store cartridge in a cool, dry place at temperatures above 40°F (5°C) and
below 100°F (38°C). Take unwanted product to an approved household hazardous waste transfer facility. Hardened material
may be disposed of with trash.
Label Precautions:
CAUTION! Contains ethylene glycol, butyl acetate and crystalline silica. May cause eye, skin and respiratory irritation. Avoid
contact with eyes and skin. Use with adequate ventilation. Do not swallow. FIRST AID: If swallowed do not induce vomiting; call
a physician or Poison Control center. For eye contact flush with water for 15 minutes. For skin contact wash thoroughly with
soap and water. If affected by inhalation, get fresh air. KEEP OUT OF THE REACH OF CHILDREN.
WARNING! This product contains chemicals known to the State of California to cause cancer.
Refer to the Safety Data Sheet (SDS) for further information.
Disclaimer:
The information and recommendations contained herein are based on our research and are believed to be accurate, but no
warranty, express or implied, is made or should be inferred. Purchasers should test the products to determine acceptable quality
and suitability for their own intended use. Nothing contained herein shall be construed to imply the nonexistence of any relevant
patents or to constitute a permission, inducement or recommendation to practice any invention covered by any patent, without
authority from the owner of the patent.