Datasheet

Technical Data Sheet
LOCTITE
®
7063™
May-2005
PRODUCT DESCRIPTION
LOCTITE
®
7063™ provides the following product
characteristics:
Technology Solvent cleaner
Chemical Type Isoparaffin, Dimethoxymethane and
Ethanol blend
Appearance Clear colorless solution
LMS
Viscosity Very low
Cure Not applicable
Application Surface cleaner
LOCTITE
®
7063™ is a non-CFC solvent based formulation for
cleaning and degreasing of surfaces to be bonded with Loctite
®
adhesives. The product can also be used for cleaning and
degreasing machine components during maintenance
operations.
TYPICAL PROPERTIES
Specific Gravity @ 25 °C 0.74
Infrared Spectrum As standard
LMS
Viscosity @ 20°C, mPa·s (cP) 2
Drying Time at 20 °C, seconds ≤60
TLV (ACGIH), ppm 600
Flash Point - See MSDS
TYPICAL PERFORMANCE
LOCTITE
®
7063™ has no effect on the speed of cure or final
strength of Loctite
®
adhesives other than providing a clean
surface for good adhesion and adhesive cure. Unclean or
partially cleaned surfaces can affect adhesive performance.
HANDLING PRECAUTIONS
Cleaner must be handled in a manner applicable to highly
flammable materials and in compliance with relevant local
regulations
Special care must be taken to avoid contact of the product or
its vapour with naked flame or any electrical equipment that is
not flame proofed
The solvent can affect certain plastics or coatings. It is
recommended to check all surfaces for compatibility before
use.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected
with a sealant for chlorine or other strong oxidizing
materials.
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Directions for use
1. Treat surfaces to be cleaned by spraying or wiping
surfaces with a solvent soaked paper towel.
2. Wipe surfaces when still wet with clean paper towel to
ensure contaminants and excess solvent are removed.
3. Repeat cleaning process if necessary.
4. Allow the solvent time to evaporate until the surfaces are
completely dry.
5.
Apply the Loctite
®
adhesive immediately and assemble
bond.
Loctite Material Specification
LMS
LMS dated December-01, 2004. Test reports for each batch
are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
The product is classified as flammable and must be stored in
an appropriate manner in compliance with relevant
regulations. Do not store near oxidizing agents or combustible
materials. Store product in the unopened container in a dry
location. Storage information may also be indicated on the
product container labelling
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
cannot assume responsibility for product which has been
contaminated or stored under conditions other than those
previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representive
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically