SECURE INSTALLATION GUIDE LATCH EDITION PGD628 | PGD628F | PGD628FC
Welcome! This guide will walk you through step-by-step how to install and get your Lockly Secure up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: Lockly.com/support or call (669) 500-8835 for help.
Preparation To complete the installation you will need: Phillips Screwdriver Pliers Flathead Screwdriver Tape measure or ruler Screwdriver with drill bits （Optional） Drilling is not required to install the lock, and is optional. However if you are installing your lock on a brand new door, a drill is required if there are no holes prepared for lock installation.
Preparation Remove existing door hardware, latch or deadbolts before installing the new lock. Use provided template to bore new holes if needed. 1-3/8" ~ 2" (35mm ~ 50mm) * 1/2" 12mm * 1" 4-1/8" 105mm 25mm 1 Measure and confirm your door is between 1-3/8" ~ 2" (35mm - 50mm). 2 Measure and confirm the hole in the door door is 2-1/8" (54mm). 3 Measure and confirm that the backset is between 2-3/8" (60mm) to 2-3/4" (70mm). 4 Measure and confirm that hole in the door edge is 1" (25mm).
Step 1 INSTALLING THE LOCKSET To ensure normal functions and stable long-term operation of this lockset, replace your door’s old lockset with the provided Lockly lockset. The included lockset is designed and optimized for Lockly smart locks. 2-3/8" (60mm) Measure the distance between center of front door hole to the edge of your door. Push the shaft (a) to adjust the lockset to 2-3/8"(60mm) or 2-3/4"(70mm).
Step 2 CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS The lock ships with handle default for right in-swing or left out-swing door. Check the diagram below if you are unsure of you door orientation. RIGHT IN-SWING DOOR LEFT IN-SWING DOOR INTERIOR Hinge Side LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR EXTERIOR LEFT-IN SWING and RIGHT OUT-SWING DOORS require changing the door handle orientation. Contnue to follow Step 2 to change exterior and interior door handle orientation.
Step 2 continued CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS 3 4 Rotate the handle 180° to the other side of the lock. Confirm that your installation was complete by checking if the pins are flush against the handle, and has popped out. Adjust the handle accordingly to make sure the pins are fully decompressed and sits flush against the surface. Using your fingers, press the two pins located on the left and right side of the the lock to insert the handle back onto the lock.
Step 2 continued CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS Changing the Interior Handle Orientation 1 2 Securely screw clockwise as shown to complete your handle orientation change. Remove the screw by turning counter clockwise and rotate the handle 180° in the direction of the arrow as shown. Make sure the screw hole is aligned with the marker as illustrated.
Step 3 PREPARING LOCK FOR INSTALLATION If you drilled a hole in Preparation, use Slotted Barrel Extension U and use pliers to securely tighten clockwise. If you did not drill a hole in Preparation, you can leave this pole removed. 4 Peel paper layer OFF the Adhesive tape and prepare for installation. U 1 2 3 D Install Spindle C with the holes side into the base of the lock and align the holes locate in the 3 o’clock and 9 o’clock position. Insert locking pin D in to the hole as shown above.
Step 4 INSTALLING THE LOCK (EXTERIOR) Exterior 1 Install the exterior lock as shown to the left by aligning the lock straight and passing the cable and attached rods through the lockset. 3 2 Pass the Spindle C through the center of the lockset, and the round rods through the sides in their respective holes. The cable should run underneath the lockset. 9 Align the lock straight and press hard (if you use the Adhesive tape in step 3.4) to secure the top of the lock.
Step 5 INSTALLING THE LOCK (INTERIOR) Interior 1 Insert Positioning Rods V into the holes to the left and right of the Spindle C . The holes are located at the 3 o’clock and 9 o’clock positions. V 2 Mounting Plate LK Interior Mounting Plate LK will go against the interior side of your door. Remove the paper layer off of the Adhesive Tape and align the positioning rods on the bottom of the plate to the corresponding left and right holes. Install the side with the black plastic seal against the door.
Step 5 INSTALLING THE LOCK (INTERIOR) continued Secure with O1 or O2 3 LK Pull the cable from the lock exterior through the rectangular hole underneath the positioning rods and spindle. Secure the hole above the spindle with screws O . 4 *Secure top with M1 or M2 Remove the position rods V and replace them with screws O Tighten clockwise until the mounting plate is secure.
Step 5 5 INSTALLING THE LOCK (INTERIOR) continued Plug X cable that is coming through the door into the lock interior Y . Match red side of the plug with red on socket - insert tightly. Install Cable Remove Cable X Y 2 1 IMPORTANT: If you need to disconnect this cable, use a screwdriver to hold down the tab (marked red) before carefully unplugging. DO NOT FORCE as this may result in damaging the lock.
INSTALLING THE LOCK (INTERIOR) continued 7 P 3x 8 -+ +- Step 5 Once the lock interior is flush against the mounting plate, secure the lock to the plate by screwing clockwise using provided screws P . Insert 4 AA batteries into the lock by aligning the positive + and negative - orientation markings on the batteries to the battery chamber. Secure the battery cover by sliding the cover over the lock and turning the screw clockwise on top until tight.
Step 6 INSTALLING THE DOOR STRIKE Close your door to see if your lock closes securely with your existing door strike. If the lock closes securely, you may keep the existing door strike without removing the old hardware. However, it’s recommended that you use our door strike. G（2X） H DOOR STRIKE INSTALLATION F Make sure the slanted side of Latchbolt F is closing against the slanted part of Strike Plate H before fixing it on to door frame.
Step 7 DOWNLOAD THE LOCKLY APP Congratulations! You have completed the Lockly Secure physical lock installation. To complete your setup, download the Lockly app from the App Store or on Google Play and follow on-screen instructions. Scan or visit Lockly.
Add more Smart to your Home Secure Link Wi-Fi Hub Add the optional Lockly Secure Link Wi-Fi Hub, together with the free Lockly app, it's easier than ever to securely control and manage your door from anywhere, anytime. Real-time, monitoring, & status Monitor open/closed door status with real-time alerts sent to your smart phone, no matter where you are. Control your Lockly from anywhere. Grant access, even when you’re not home Lock and unlock door from anywhere.
FCC Warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. If you wish to change the orientation of the lock for a Left Swing door, follow instructions on Installation Guide (Step 2).
SECURE Go to Lockly.com/installation to download the latest version of this installation guide. OR Scan the code on your phone to watch step-by-step video installation.
SECURE For the latest version of this manual, please visit the following link: Lockly.com/help We’re here to help! help@Lockly.com © Copyright 2023 Lockly All rights reserved US Patent NO. US 9,881,146 B2 | US Patent NO. US 9,853,815 B2 | US Patent NO. US 9,875,350 B2 | US Patent NO. US 9,665,706 B2 | US Patent NO. US 11,010,463 B2 | AU Patent NO. 2013403169 | AU Patent NO. 2014391959 | AU Patent NO. 2016412123 | UK Patent NO. EP3059689B1 | UK Patent NO.
