Installation Sheet

6. Replace the cover plate and secure with four (4) Red Screws,
using a #2 screwdriver.
7. TEST CODE before installing/re-installing lock.
3. PRESS & HOLD ‘C’ BUTTON to release tumblers.
IMPORTANT: ‘C’ buon MUST be pressed and held down when
removing and inserng tumblers. Failure to do so will damage
the lock and void the warranty.
WARNING:
Do NOT force tumblers into posion!
4. While holding the ‘C’ BUTTON, remove/add CODE (Red) and
NONCODE (Blue) tumblers to create your desired code.
Ex: 3 Red = 3-Digit Code / 6 Red = 6-Digit Code
5. Aer changing your code, release the ‘C’ BUTTON to secure the
tumblers in place.
INSTALLATION INSTRUCTIONS CONTINUED:
How to Change User Code/Combinaon
SAVE
For more helpful ps and installaon instrucons, visit www.LOCKEYUSA.com
Step 5: Install Lever Handles
Using Allen Wrench (#7), install levers to the inside and outside bodies.
Secure with set screws.
Note: Levers should point towards the door hinges.
The 2985 is equipped with a built-in slip clutch lever handle to prevent damage in
the event of an aempted forced entry.
If lever handle is in posion shown (far right), pull lever back to desired posion.
Step 6: Verify Correct Spindle Length (Fig. 6)
With the Deadlatch installed, hold the Inside Body (#2) and Rubber Trim Plate (#4) to the door.
Place Spindle (#6) through Latch, into the Inside Body, as far as possible.
Spindle should extend from exterior of door 3/8” min. to 5/8” max.
If Spindle is too long, cut it to the correct length using pliers.
*IMPORTANT:
If spindle extends less than 3/8” it may not engage the lock.
If spindle extends more than 5/8”, it will cause the lock to bind.
Step 7: Install the 2985
Place the Rubber Trim Plate (#4) on the backside of the Outside Body (#1).
Place the Outside Body on the door. The Hex Bolts (#15) should extend into the top and bottom holes.
The Support Pin (#13) should extend through the hole in the Latch (#12).
Insert the Spindle (#6) into the Outside Body (#1) ensuring it’s in the proper angled posion.
*IMPORTANT: SPINDLE POSITION/ANGLE
RIGHT-HAND DOORS: From inside, place spindle through Latch, into the Outside Body in the 2:00/8:00 posion (Fig. 7).
LEFT-HAND DOORS: From inside, place spindle through Latch, into the Outside Body in the 10:00/4:00 posion (Fig. 8).
Place the Rubber Trim Plate (#4) and Inside Body (#2) on the inside of the door.
Using a screwdriver, secure the lock to the door with Screws (#9)(Screw length dependent on door thickness).
Test the operaon of the latch by turning the inside lever.
Locate posion where latch strikes door frame and install Strike Plate (#5).
TEST YOUR LOCK: Press ‘C’ buon (clear), followed by your combinaon. Push lever down and lock will open.
TEST PASSAGE: Press ‘C’, followed by ‘Y’, followed by combinaon. Lock should remain unlocked (passage).
TO LOCK: Push ‘Y’, followed by ‘C’. Lock will remain locked.
Aer installing and tesng the lock, secure Faceplate (#16).
NOTE: If lever handle must be pulled up to unlock, change spindle posion/angle (see figures 7 and 8).
If latch scks: First, make sure Support Pin (#13) is in place. Second, verify correct spindle length (see step 6).
1. Using a #2 screwdriver, remove the four (4) Red Screws.
2. Carefully remove cover plate.
WARNING: Springs are aached to plate.
‘C’ = CLEAR (DO NOT REMOVE)
‘Y’ = PASSAGE (‘Y’ Tumbler may be removed to disable PASSAGE FUNCTION)
2:00
8:00
Fig. 7
10:00
4:00
Fig. 8.
Slip Clutch
Fig. 6
= 3/8” to 5/8”


Updated 3.21.16