User's Manual Part 1
GS550 UNDERHOOK
5
ChApTEr 2: iNSTALLATiON
2.2 Start-Up
Figure: Key components in a typical system installation. Your product may vary. Not to scale.
Under Hook
GS550 Display
Load Cell
TAR. LIM.
MENU
GS550
%
0
1020 30 4050
60
7080
9
0100110
.
M
I
L
.
RAT
MEN
U
GS5 50
%
0 1020 30 4050 6070 80
901
0
0
1
10
Underhook
.
M
IL
.RAT
MEN
U
GS5 50
%
0 1
0
2
0
3040 50
6070 80 90100110
Underhook
ThE gS550 uNdErhOOK SySTEm iS
dESigNEd AS AN OpErATOr Aid ANd
iS iN NO wAy A SuBSTiTuTE FOr SAFE
OpErATiNg prACTiCES.
WARNING
InstallatIon must be made In
complIance wIth lsI-Robway
InstRuctIons and usIng lsI-Robway
supplIed components only.
FAiLurE TO iNSTALL ALL pArTS, Or
rEpLACiNg pArTS Or COmpONENTS wiTh
pArTS Or COmpONENTS NOT SuppLiEd
By LSI-ROBWAY, mAy LEAd TO SySTEm
FAiLurE, SEriOuS iNJury Or dEATh.
WARNING
The GS550 Underhook must be correctly
programmed for the system sensors installed. If a
sensor is missing or has a problem, a message will
be displayed on the GS550 Underhook. Press the
Info button to get more details on the problem.
This process may take up to one minute. The delay
is created by the battery management function.
Press and hold the Exit button to temporarily stop
the buzzer if needed.
iF ThE NuTS ArE ON ThE OuTSidE OF ThE
CAB, CAuLK wiTh SiLiCONE BETwEEN
ThE wAShErS ANd ThE CAB TO prEvENT
wATEr ENTry.
NOTE
✓
2.3 Load Cell
CApACiTy FOr LOAd CELLS ANd
ShACKLES/ACCESSOriES ArE
CALCuLATEd FOr LOAdS ALONg ThE
iNTENdEd AXiS OF LOAd (vErTiCAL ON
hOOK ASSEmBLiES, hOriZONTAL whErE
ApprOpriATE); SidE LOAdiNg Or TwiSTiNg
mAy CAuSE uNduE STrESS ON ThE LOAd
CELL/LiFTiNg ACCESSOriES CAuSiNg
LOAd drOpS. RIggIng must be done
In a way that twIstIng Is avoIded to
pRevent sIde loadIng.
WARNING
ThE LOAd CELL muST BE CENTErEd ON
ThE ShACKLE TO AvOid uNEvEN LOAdiNg
ON ThE pLATE KiT ASSEmBLy.
CAUTION
ThE LOAd CELL ANTENNA ShOuLd NOT BE
iN CONTACT wiTh mETAL.
CAUTION
FOr OpTimAL pErFOrmANCE ANd SigNAL
rECEpTiON, ENSurE A CLEAr LiNE OF
SighT BETwEEN ThE LOAd CELL ANTENNA
ANd ThE gS550 uNdErhOOK diSpLAy.
CAUTION