FCC ID: VVXLM068 IC: 10531A-LM068
v1.0 06/03/2019 Merged LM961, LM068 and LM074 manuals. Modified the content as per SPPC_0115 firmware version. V1.2 12/03/2019 Changes for SPPC_0115 firmware. Changed the section numbering. Added support for UART FW upgrade interface. V1.3 06/19/2019 Added changes for Version SPPC_0201.
• •
AT*UPDATENAME Query and set ON
2
at*addr=?at*addr=? REP*:ADDR=0002-5b-080419 OK at*name=?at*name=? OK REP*:NAME=068SerialADT19 at*ver=?at*ver=? OK REP*:VER=068LM_SPP+GAPCEN_02.
at*addr=?at*addr=? REP*:ADDR=34c9-f0-8119f9 OK at*updatename=?at*updatename=? OK REP*:UpdateName=ON at*name=?at*name=? OK REP*:NAME=068SerialADTF9 at*name=testsnameat*name=testsname OK at*name=?at*name=? OK REP*:NAME=testsnameF9 at*updatename=offat*updatename=off OK at*name=testsnameat*name=testsname OK at*name=?at*name=? OK REP*:NAME=testsname at*updatename=onat*updatename=on OK at*name=?at*name=? OK REP*:NAME=testsnameF9
at*ver=?at*ver=? OK REP*:VER=068LM_SPP+GAPCEN_01.
at*settings=?at*settings=? OK NAME=068SerialADT19 ADDR=0002-5b-080419 PAIR=ON DCOV=ON BAUD=19200(2) STOP=Stop_One(0) PARITY=None(0) FLOW=OFF ECHO=ON RESP=ON MODEM=NONE SPPRole=SLAVE ACON=OFF BOND=0000-00-000000 RICD=OFF DPIN=ON MITM=ON IOTYPE=KB_Only ENBGAP=OFF VER=068LM_SPP+GAPCEN_02.
PAIR=ON DCOV=ON BAUD=19200(2) STOP=Stop_One(0) PARITY=None(0) FLOW=OFF ECHO=ON RESP=ON MODEM=NONE SPPRole=SLAVE ACON=OFF BOND=0000-00-000000 RICD=OFF DPIN=ON MITM=ON IOTYPE=KB_Only ENBGAP=ON LE_SEC=OFF LE_AUTO_SCAN=ON VER=068LM_SPP+GAPCEN_02.
at*UARTconf=?at*UARTconf=? OK REP*:UART_CONFIG=UART_THROUGHPUT at*UARTconf=throughputat*UARTconf=throughput ERR at*UARTCONF=Latencyat*UARTCONF=Latency OK Device will Reboot SPP+GapCentral_Message_Loop at*UARTCONF=?at*UARTCONF=? OK REP*:UART_CONFIG=UART_LATENCY at*UARTCONF=latencyat*UARTCONF=latency ERR at*UARTCONF=throughputat*UARTCONF=throughput OK Device will Reboot SPP+GapCentral_Message_Loop
• • •
•
at*UARTCONF=?at*UARTCONF=? OK REP*:UART_CONFIG=UART_LATENCY at*UPGRADEINT=?at*UPGRADEINT=? OK REP*:UPGRADEINT=UART at*UPGRADEINT=UARTat*UPGRADEINT=UART ERR at*upgradeint=OTAat*upgradeint=OTA OK at*upgradeint=?at*upgradeint=? OK REP*:UPGRADEINT=OTA at*upgradeint=OTAat*upgradeint=OTA
ERR at*UPGRADEINT=UARTat*UPGRADEINT=UART OK at*upgradeint=?at*upgradeint=? OK REP*:UPGRADEINT=UART
at*enbgap=?at*enbgap=? OK REP*:GAP_ENABLE=OFF at*settings=?at*settings=? OK NAME=LM068_GAP_Central ADDR=0002-5b-00a5a5 FLOW=OFF SPPRole=SLAVE ACON=OFF BOND=0000-00-000000 DPIN=OFF PIN=1234 GAP_ENABLE=OFF VER=074LM_GAPCEN_01.06 REP*:SETTINGS=END at*enbgap=offat*enbgap=off ERR at*enbgap=onat*enbgap=on OK Adapter soft-Reset..
OK NAME=LM068_GAP_Central ADDR=0002-5b-00a5a5 FLOW=OFF SPPRole=SLAVE ACON=OFF BOND=0000-00-000000 DPIN=OFF PIN=1234 GAP_ENABLE=ON LE_SEC=OFF LE_AUTO_SCAN=ON VER=074LM_GAPCEN_01.06 REP*:SETTINGS=END at*enbgap=?at*enbgap=? OK REP*:GAP_ENABLE=ON at*enbgap=onat*enbgap=on ERR at*enbgap=offat*enbgap=off OK Adapter soft-Reset..
REP*:BLE_SCAN_REP=START = 1 :1028-00-5b0002 :0 = 2 :1032-00-5b0002 :0 = 3 :3333-33-333333 :0 = 0: 3333-33-333333, LM Serial = 4 :8863-df-be936c :0 :LML8 = 5 :0000-00-000000 :3 = 6 :1029-00-5b0012 :0 :CSR BP = 7 :1030-00-5b0012 :0 :CSR HR = 8 :1031-00-5b0012 :0 :CSR HR at*lefind=offÑlefind=off at*lefind=offat*lefind=off OK” Server Sensor Sensor Sensor
at*lefind=onat*lefind=on OK REP*:BLE_SCAN_REP=START = 1 :1032-00-5b0002 :0 = 2 :1028-00-5b0002 :0 = 3 :3333-33-333333 :0 = 0: 3333-33-333333, LM Serial Server = 4 :8863-df-be936c :0 :LML8 IND*:CONNECTED=0012-6f-0819c2 +++OK = 7 :2053-ca-20126e :0 = 8 :2053-ca-20126f :0 at*lefind=offat*lefind=off OK
at*leconn=1030005b0012at*leconn=1030005b0012 OK REP*:BLE_CONNECTED:=1030-00-5b0012-0 : 1 : 0080 : 0017 : 0008 BLE Auth start OK REP*:SERVICE START: =1030-00-5b0012 = 1 : 1801 : 0001 : 0004 = 2 : 1800 : 0005 : 000b = 3 : 180d : 000c : 0013 = 4 : 180f : 0014 : 0017 REP*:BLE_PAIR=1030-00-5b0012,Success = 5 : 00001016d10211e19b2300025b00a5a5 : 0018 : 0021 = 6 : 180a : 0022 : ffff REP*:SERVICE END: =1030-00-5b0012
at*ledrop=1030005b0012at*ledrop=1030005b0012 OK REP*:BLE_DIS_CONN:=1030-00-5b0012,2 err_code:0000
