Installation Guide

ASSEMBLING & INSTALLATION INSTRUCTIONS PRODUCT#
1344 1345 1349
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING THE FIXTURE (Fig.2).
1. Return the arms to suitable position.
2. Attach the pipe(A) to the top center pipe screw of the fixture body(D),
by turning it clockwise until tight.
3. Attach the glass shade (C) to the lamp holder, lock it securely with check
ring(B).
4. Install the light bulbs in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
HANGING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old single bar.
2. Carefully unpack new fixture and lay all the parts on a clear su
rface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other e
nd of nipple (C) with loop attached into singl
e bar (D)
until snug.
5. Place lock
washer (B) over end of nipple protruding through si
ngle bar
and thread hex
nut (A) onto ni
pple until tight.
6. T
ake this single bar assembly and mount to ceiling junction box with
junction box screws (E). Tighten screws securely with screwdriver.
7. Using proper chain pliers to open one end link of the chain provided
and connect to the fixture loop (I). Close the li
nk.
8. By measuring, determine correct number of links needed for proper
hanging height. Using proper chain pliers disconnect and discard
re
maining chai
n.
9. Lace the fixture wires through the chain.
10. Slip loop collar
(H) over the chain, then do the same with the canopy
(G).
11. Open the other end link of the chain and hang the fixture on th
e loop
at the ceiling. Close the link.
12. Feed the fixtur
e wires through the loop (F) and nipple (C) and pull
until taut.
13. Slide canopy
(G) up flush to ceiling, secure us
ing loop (H).
CONNECTING THE WIRES (Fig.3)
1. Take the black wire from the ceiling junction box and the smooth wire
leg fro
m the fixture and twist bare ends together. Twist wire connector
onto end of wire until snug.
2.
Repeat same process with white junction box wire and ri
bbed wire leg
of fixture wire.
NOTE: Twist wires together in the same direction you
twist the wire connector onto wires.
3.
If your junction box has a grounding
wire (green or bare copper),
attach this wire
and the bare copper wire from th
e fixture together as
step 1.If
junction box has no ground wire,
attach the bare copper
fixture wire to t
he green ground screw on the single bar.
4. Tuck these wire connections neatly into the ceiling outlet box and then
raise the canop
y (G) all the way to the ceiling
. Raise the loop (H) and
thread onto ceil
ing loop protruding through canopy
.
Your installation is now complete. Return power to the
junction box and test the fixture.
Fig.1
I
H
CHAIN
G
F
E
D
A
B
C
Junction Box
(Not included)
Fig.2
$
'
%
&
Fig.3
:KLWHRU
+286(
%ODFN
:,5(6
+RW
6PRRWK
),;785(
:,5(6
%ODFNRU
5LEEHG
:,5(6
),;785(
%DUH&RSSHU*URXQG
),;785(
:,5(6
&RSSHU
*URXQG
+286(
1HXWUDO
:,5(6
:KLWH
%DUH
*UHHQRU
:,5(6
+286(
DOC20141201344