B344231344COM0
4231344COM Nightstand Keep this Assembly Manual for future reference. Las traducciones en español se encuentran al final de este manual. Vous trouverez les traductions en français à la fin de ce manuel. Two adults recommended for assembly Secure Your Furniture Do NOT return this product. Keep your home and family safe with the wall anchor kit that is included with the product. For missing or broken parts - Visit littleseedskids.
Do NOT return this product! Contact our friendly customer service team first for help. Assembly Tips Call us! 1‐800‐489‐3351 Monday‐Friday 9am ‐ 5pm CST You Tube Visit littleseedskids.com to view the limited warranty valid in the U.S. and Canada.
Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Give yourself enough room for the assembly process Have the following tools: Flat Head Screwdriver, #2 Phillips Head Screwdriver and Hammer Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.
Board Identification B A C Left Panel 34231344010 Left Panel 34231344020 D Top 34231344030 F G Bottom 34231344040 I H E Drawer Front 34231344090 Rail 34231344050 x2 Right Front Molding Rear Molding Left Front Molding 34231344070 34231344080 34231344060 J Drawer Bottom 39991341038410D littleseedskids.com DWR BACK DWR SIDE This piece is paper board construction. It is not made from wood but is required for the assembly of your unit.
Board Identification This piece is paper board construction. It is not made from wood but is required for the assembly of your unit. C K B G E H A F D DWR SIDE DWR BACK J DWR SIDE littleseedskids.
Parts List Actual Size 1 2 (x10) #A22610 cam bolt 3 (x10) #A22620 cam lock 4 (x6) #A21660 wood dowel (x10) #A11080 7/16" flat screw 6 7 (x12) #A12950 1‐1/8" flat head (x24) #A21110 nail (x8) #A12120 7/16" pan screw 9 8 (x2) #A17300 3/4" truss 5 (x4) #A21970 drive fastener Not Actual Size 13 11 15a 15b 15c 10a left cabinet member 10b right cabinet member 10c left drawer member 10d right drawer member (x1) #A56770 drawer slide pkg. littleseedskids.
Step 1 6 6 (x6) #A12950 6 6 6 A 6 H 6 F Be sure all edges are flush with each other. Note: Finished edge of left panel (A) will sit into the left front molding (F) as shown. A A H littleseedskids.com end view F F Note: Screw through panel and into groove in moldings.
Step 2 1 3 2 (x3) #A22610 Quick (x2) #A22620 Assembly Tip 4 (x1) #A21660 (x3) #A11080 Proper orientation of CAM LOCK marked with a "L" 10a left cabinet member (x1) #A56770 1 2 1 A 1 10a H 2 3 littleseedskids.
Step 3 6 (x6) #A12950 6 6 6 6 B 6 H 6 G Note: Finished edge of right panel (B) will sit into the right front molding (G) as shown. Be sure all edges are flush with each other. B G B G Note: Screw through panel and into groove in moldings. littleseedskids.
Step 4 1 2 (x3) #A22610 Quick 3 (x2) #A22620 Assembly 4 (x1) #A21660 Tip (x3) #A11080 Proper orientation of CAM LOCK marked with a "R" 10b (x1) #A56770 1 1 2 B 1 10b H 2 4 G 10b littleseedskids.
Step 5 Quick 3 2 Assembly Tip (x6) #A22620 (x4) #A21660 2 Proper orientation of CAM LOCK 2 3 2 D 2 3 2 E 2 3 littleseedskids.
Step 6 Finished edges will face up. UNLOCK A E D littleseedskids.
Step 7 UNLOCK B E A littleseedskids.
Step 8 15a 15b 1 (x4) #A22610 (x1) #A84050 15b Do not fully tighten this screw. 15a 1 1 1 C 1 finished edge littleseedskids.
Step 9 Finished edges will face up. UNLOCK C A B littleseedskids.
Step 10 8 (x24) #A21110 IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT AND MUST BE INSTALLED PROPERLY. With the help of another person, carefully turn your unit over on its front side. Make sure the unit is square. Position the back panel as shown. Align the back panel equally with outside edges and nail straight through into back edges as shown. Assure that the unit is square. Distance from corner to corner must be equal as shown.
Step 11 13 (x4) #A53570 14 (x2) #A53580 14 C 14 13 F 13 G 13 13 littleseedskids.
Step 12 5 11 (x4) #A12120 (x2) #A54510 DWR SIDE 11 11 5 5 5 5 bracket orientation bracket orientation littleseedskids.
Step 13 5 (x4) #A12120 5 DWR SIDE 5 DWR SIDE I Be sure the groove in the drawer sides are centered with the groove in the drawer front (I). littleseedskids.
Step 14 9 Insert the drawer bottom (J) into the grooves as shown. Position the drawer back as shown and secure by lightly tapping the drive fasteners (9). (x4) #A21970 9 9 DWR BACK DWR SIDE J "finished surface" 9 9 DWR SIDE I littleseedskids.
Step 15 7 left drawer member 10c 4 (x4) #A11080 right drawer member 10d (x1) #A56770 (x2) #A17300 12 (x1) #A52575 10d Attach slides before attaching the handle. 4 DWR SIDE 10c 4 7 DWR SIDE 7 I 12 littleseedskids.
Step 16 15c For Masonry, Concrete, or other wall materials: Consult your local hardware store for appropriate anchors to securely attach the safety bracket. 15d IMPORTANT: THIS UNIT MUST BE SECURE TO THE WALL TO HELP PREVENT TIPOVER. FOLLOW THESE INSTRUCTIONS TO INSTALL THE ANTI‐TIPPING SAFETY BRACKET PROVIDED WITH THIS PRODUCT. WARNING Serious or fatal crushing injuries can hole occur from furniture tipover.
Step 17 Note: The drawer bracket holes are slotted. Drawer front can be adjusted by loosening screws, making needed adjustments and retightening screws. cabinet member roller littleseedskids.
MAXIMUM LOADS This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. 40 lbs. 18.1 kg 15 lbs. 6.8 kg 40 lbs. 18.1 kg Warning: Risk of injury to persons ‐ do not place a television on this furniture. This furniture is not approved for use with a television. Certificate of Conformity 1. This certificate applies to the Dorel Home Furnishings, Inc. product identified by this instruction manual. 2.
Register your product to receive the following: * New trend details ‐ sneak peek on what's new * Surveys ‐ have a voice within our community * Exclusive deals and discount codes * Quick and easy replacement part service To register your product, visit littleseedskids.
Español Consejos Útiles (página 3) ‐ Abra su artículo en el área donde usted planea utilizarlo para evitar levantar y moverlo menos ‐ Identificar, ordenar y contar las piezas antes de intentar ensamblar ‐ Las clavijas de compresión se golpean con un martillo ‐ Las diapositivas están marcadas con una R (derecha) y L (izquierda) para la colocación correcta ‐ Asegúrese de que siempre este el punto locaizado en la parte superior de bloqueador de leva este volteadohacia borde exterior ‐ Utilizar todos los clavo
Español Página 10 Asegúrese de que todos los bordes estén nivelados. Nota: El borde terminado del panel derecho (B) se asentará en la moldura delantera derecha (G) como se muestra. Nota: Atornille a través del panel en la ranura de las molduras. Página 15 No apriete este tornillo completamente. Página 17 ¡IMPORTANTE! EL PANEL TRASERO ES UNA PIEZA ESTRUCTURAL DE ESTA UNIDAD Y DEBE INSTALARSE CORRECTAMENTE. Con la ayuda de otra persona, gire su unidad con cuidado sobre su lado delantero.
Español Página 23 Para mampostería, hormigón u otros materiales de pared: Pida los anclajes adecuados para colocar el soporte de seguridad de forma segura en su ferretería local. IMPORTANTE: ESTA UNIDAD DEBE ANCLARSE A LA PARED PARA PREVENIR QUE SE VUELQUE. SIGA ESTAS INSTRUCCIONES PARA INSTALAR EL SOPORTE DE SEGURIDAD ANTI‐VUELCO PROPORCIONADO CON ESTE PRODUCTO. AVISO Se pueden producir lesiones por aplastamiento graves o mortales a causa del vuelco de los muebles.
Español Página 25 CARGA MAXIMA Esta unidad ha sido diseñada para soportar la carga máxima anotada. El exceder estos límites puede causar inestabilidad, colapsarse y/o causar serias lesiones. ADVERTENCIA: Riesgo de lesiones a las personas ‐ no coloque un televisor sobre muebles. Este mueble no está aprobado para su uso con un televisor.
Français Astuces Utiles (page 3) ‐Ouvrez votre article dans la zone que vous prévoyez de le garder pour moins de levage lourd ‐Identifier, trier et compter les pièces avant d'essayer d'assembler ‐Les goujons de compression sont taraudés avec un Marteau ‐Les glissières sont marquées d'un R (droit) et d'un L (gauche) pour un bon placement ‐Assurez‐vous toujours de faire face la pointe situé sur le haut de la Serrure de Came vers le bord extérieur ‐Utiliser tous les clous fournis pour le panneau arrière et les
Français Page 10 Assurez‐vous que toutes les extrémités sont alignées. Remarque : Le bord fini du panneau de droite (B) s'installera dans la moulure avant gauche (G) comme indiqué. Remarque : Vissez à travers le panneau et dans la rainure des moulures. Page 15 Ne serrez pas complètement cette vis. Page 17 IMPORTANT! LE PANNEAU ARRIÈRE EST UNE PARTIE STRUCTURELLE DE CETTE UNITÉ ET DOIT ÊTRE INSTALLÉ CORRECTEMENT. Avec l'aide d'une autre personne, retournez soigneusement votre unité sur sa face avant.
Français Page 23 Pour la maçonnerie, le béton ou d'autres matériaux de construction de murs: Consultez votre quincaillerie pour connaître les ancrages appropriés afin de fixer solidement le support de sécurité. IMPORTANT : CE MEUBLE DOIT ÊTRE SÉCURISÉ AU MUR POUR ÉVITER QU'IL NE BASCULE. SUIVEZ CES INSTRUCTIONS POUR INSTALLER LE SUPPORT DE SÉCURITÉ ANTI‐BASCULEMENT FOURNI AVEC CE PRODUIT. AVERTISSEMENT Des blessures graves ou mortelles peuvent se produire en cas de basculement des meubles.
Français Page 25 CHARGES MAXIMALES Ce meuble a été conçu pour supporter les charges maximales indiquées. En excédant ces limites de charge, le meuble pourrait devenir instable, s'effondrer, et/ou causer des blessures graves. AVERTISSEMENT : Risque de blessure corporelle ‐ ne pas placer une télévision sur ce meuble. Ce meuble n'est pas approuvé pour une utilisation avec une télévision.
