Instruction Manual

ManualsBrandsLittelfuse ManualsHardwareSxx10x Series

267

Revised: 09/23/13

Speciﬁcations are subject to change without notice.

Teccor

brand Thyristors

10 Amp Sensitive & Standard SCRs

Sxx10xSx & Sxx10x Series

Description

Excellent unidirectional switches for phase control and

general switching applications such as heating and motor

speed controls.

Sensitive gate SCRs are easily triggered with microAmps

of current as furnished by sense coils, proximity switches,

and microprocessors.

Standard phase control SCRs are triggered with few

milliamperes of current at less than 1.5V potential.

Features & Beneﬁts

t3P)4DPNQMJBOU

t(MBTToQBTTJWBUFE

junctions

t7PMUBHFDBQBCJMJUZVQ

to 1000 V

t4VSHFDBQBCJMJUZVQ

to 100 A

Main Features

Symbol Value Unit

T(RMS)

10 A

DRM

RRM

400 to 1000 V

0.2 to 15 mA

Schematic Symbol

Agency Approval

Agency Agency File Number

TO-220L Package : E71639

Applications

Typical applications are capacitive discharge systems for

strobe lights, nailers, staplers and gas engine ignition. Also

controls for power tools, home/brown goods and white

goods appliances.

Internally constructed isolated packages are offered for

ease of heat sinking with highest isolation voltage.

Summary of content (11 pages)

PAGE 1
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Sxx10xSx & Sxx10x Series Description Excellent unidirectional switches for phase control and general switching applications such as heating and motor speed controls. Sensitive gate SCRs are easily triggered with microAmps of current as furnished by sense coils, proximity switches, and microprocessors. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential.
PAGE 2
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Absolute Maximum Ratings — Sensitive SCRs Symbol Parameter IT(RMS) IT(AV) ITSM Sxx10RSy Sxx10DSy Sxx10VSy TC = 95°C Sxx10LSy TC = 80°C Average on-state current Sxx10RSy Sxx10DSy Sxx10VSy TC = 95°C Value Unit 10 A 6.4 A 83 single half cycle; f = 60Hz; TJ (initial) = 25°C 100 I2t Value for fusing tp = 8.
PAGE 3
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Electrical Characteristics (TJ = 25°C, unless otherwise speciﬁed) – Sensitive SCRs Symbol IGT VGT Value Test Conditions Sxx10xS2 MAX. VD = 6V RL = 100 Sxx10xS3 200 MAX. 500 Unit μA 0.8 V dv/dt VD = VDRM; RGK = 1k ; TJ = 110°C TYP. 8 V/μs VGD VD = VDRM; RL = 3.3 k ; TJ = 110°C MIN. 0.2 V VGRM IGR = 10μA MIN. 6 IH IT = 20mA (initial) MAX. 6 8 mA tq (1) MAX. 50 45 μs tgt IG = 2 x IGT; PW = 15μs; IT = 12A TYP.
PAGE 4
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Thermal Resistances Symbol Parameter Value Sxx10RSy 1.6 Sxx10LSy 3.0 Sxx10VSy 1.7 Sxx10DSy 1.45 Sxx10R 1.6 Sxx10L 3.0 Sxx10V 1.7 Sxx10D 1.45 Sxx10RSy 40 Sxx10LSy 65 Sxx10VSy 85 Sxx10R 40 Sxx10L 50 Sxx10V 70 Unit Junction to case (AC) R (J-C) °C/W Junction to ambient R (J-A) °C/W Note: xx = voltage, y = sensitivity Figure 1: Normalized DC Gate Trigger Current vs.
PAGE 5
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature Figure 4: Normalized DC Holding Current vs. Junction Temperature 2.0 Ratio of IH / IH (TJ = 25°C) Ratio of VGT / VGT (TJ = 25°C) 2.0 1.5 1.0 0.5 1.5 1.0 0.5 0.0 0.0 -40 -15 10 35 60 85 110 -40 125 -15 10 Junction Temperature (TJ) -- (°C) Figure 5: On-State Current vs.
PAGE 6
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Figure 9: Maximum Allowable Ambient Temperature vs. RMS On-State Current Figure 10: Maximum Allowable Ambient Temperature vs.
PAGE 7
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Soldering Parameters Reﬂow Condition 1C o 'SFF BTTFNCMZ Pre Heat 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) o TFDT Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reﬂow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) o TFDPOET Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) o TFDPOET Ram
PAGE 8
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Product Selector Voltage Part Number 400V 600V X X Sxx10RS2 800V 1000V Gate Sensitivity Type Package 0.2mA Sensitive SCR TO-220R Sxx10LS2 X X 0.2mA Sensitive SCR TO-220L Sxx10VS2 X X 0.2mA Sensitive SCR TO-251 Sxx10DS2 X X 0.2mA Sensitive SCR TO-252 Sxx10RS3 X X 0.5mA Sensitive SCR TO-220R Sxx10LS3 X X 0.5mA Sensitive SCR TO-220L Sxx10VS3 X X 0.5mA Sensitive SCR TO-251 0.
PAGE 9
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount Anode E D 6.71 .264 5.28 .208 TC MEASURING POINT Dimension 6.71 .264 B C P Q Cathode GATE F Anode 1.60 .063 1.80 .071 AREA : 0.040 IN2 3 .118 G 4.60 .181 I O L K J H M N Sxx10xSx & Sxx10x Series 275 Millimeters Min Typ Max Min Typ Max A 0.037 0.040 0.043 0.94 1.01 1.09 B 0.235 0.243 0.245 5.97 6.16 6.22 C 0.106 0.108 0.113 2.69 2.74 2.87 A 5.
PAGE 10
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead AREA (REF.) 0.17 IN2 TC MEASURING POINT O A E Dimension 8.13 .320 P ANODE B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H CATHODE ANODE GATE K N Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). M J Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.
PAGE 11
Teccor® brand Thyristors 10 Amp Sensitive & Standard SCRs Packing Options Part Number Marking Weight Packing Mode Base Quantity Sxx10L/Ryy Sxx10L/Ryy 2.2 g Bulk 500 Sxx10L/RyyTP Sxx10L/Ryy 2.2 g Tube 500 (50 per tube) Sxx10DyyTP Sxx10Dyy 0.3 g Tube 750 (75 per tube) Sxx10DyyRP Sxx10Dyy 0.3 g Embossed Carrier 2500 Sxx10VyyTP Sxx10Vyy 0.4 g Tube 750 (75 per tube) Sxx10L/R Sxx10L/R 2.2 g Bulk 500 Sxx10L/RTP Sxx10L/R 2.2 g Tube 500 (50 per tube) Sxx10DTP Sxx10D 0.