Installation Guide

ManualsBrandsLithonia Lighting ManualsCommercial LightingContractor Select 24" Wide LED Strip Light

INSTALLATION INSTRUCTIONS

RLNK LED Linkable Strip

*Model number noted on carton label

TOOLS REQUIRED

FOR INSTALLATION

• Safety glasses

• Drill with 1/16” drill bit

• Phillips screwdriver

• Pencil

• Hammer

• Pliers

• Ruler

• Wire Strippers

OUTILS REQUIS POUR L’INSTALLA-

TION

• Lunettes de sécurité

• Perceuse, avec un foret de 1/16 po

• Tournevis à tête Phillips

• Crayon

• Marteau

• Pinces

• Régle

HERRAMIENTAS NECESSARIAS PARA

LA INSTALACIÓN

• Lentes de seguridad

• Taladro con broca de 1/16”

• Destornillador de Phillips

• Làpiz

• Martillo

• Pinzas

• Regla

• Pelacables

U219970T Rev C 09/20

Protect yourself. Before installing,

read these instructions carefully and

save them for future reference.

Date Installed:________________

Pour votre propre protection. Avant de procéder

à l’installation, veuillez lire attentivement ces

directives et les conserver pour référence ultérieure.

Date de l’installation :

________________

Protéjase. Antes de instalar, lea estas

instrucciones cuidadosamente

y guárdelas para futura referencia.

Fecha Instalada:________________

2ft LED Strip

RLNK L24

actual length: 22-3/4” (57.9cm)

4ft LED Strip

RLNK L48

actual length: 46-3/8” (117.9cm)

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS RLNK LED Linkable Strip *Model number noted on carton label AN AR G Safety glasses Drill with 1/16” drill bit Phillips screwdriver Pencil Hammer Pliers Ruler Wire Strippers Pour votre propre protection. Avant de procéder à l’installation, veuillez lire attentivement ces directives et les conserver pour référence ultérieure.
PAGE 2
LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION • To reduce the risk of death, personal injury or property damage from ﬁre, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the ﬁxture box and all ﬁxture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 3
4 2 8 7 3 12 1 13 5 10 11 6 9 FIXTURE PACKING LIST LISTA DE EMBALAJE Description Quantity 1) Housing Assembly ........................... 1 2) LED Cover assembly ......................... 1 3) LED Driver ........................................ 1 4) Wire Connectors ............................... 3 5) Rocker Switch ................................... 1 6) “Keyed” connector port ...................... 1 7) Standard connector port .................... 1 8) Push-in wire connector ................
PAGE 4
PREPARING THE FIXTURE FOR INSTALLATION Remove fixture components and parts pack(s). Check that all parts are included. See Page 3. Note: A single unit or the first unit in a chain is capable of being direct-wired to incoming power or use the optional power-cord to supply power. You will need to determine which method prior to installing the product. If multiple units are to linked together (max. 18 fixtures), the suppliled row connector or the linking cords will be required.
PAGE 5
PREPARÁNDOSE PARA LA INSTALACIÓN Saque los componentes del luminario y paquete(s) de piezas. Compruebe que todas las piezas estén incluidas. Vea página 3 PRÉPARATION DE L’APPAREIL POUR L’INSTALLATION Retirer les composantes de l’appareil et tout emballage de pièces. S’assurer que toutes les pièces sont incluses.
PAGE 6
12. Once the first fixture is mounted, you can install the next fixture in the chain. On the end(s) of fixture to be connected- remove plug cover- See Fig 5. Note: Fixture orientation is important- make sure all of the linked fixtures are oriented the same way. The linking cord must connect to a Keyed port on one fixture and a non-keyed port on the other fixture. 13. Mount remaining fixture(s) as stated in the previous steps with included Row Connector (11) or 18” Linking Cord.
PAGE 7
12. Una vez que el primer luminaria está montado, usted puede instalar el siguiente en el circuito.En los extremos del montaje que se conectará: quite la cubierta del enchufe, Vea fig 5. Nota: La orientación del montaje es importante: asegúrese de que todos los montajes conectados estén orientados de la misma forma. El cable de unión debe conectarse a un puerto con chaveta en un montaje y a un puerto sin chaveta en el otro montaje. 13.
PAGE 8
Note: Fixture orientation is important- make sure all of the linked fixtures are oriented the same way. The linking cord must connect to a Keyed port on one fixture and a non-keyed port on the other fixture. 8. Una vez que el primer luminaria está montado, usted puede instalar el siguiente en el circuito. En los extremos del montaje que se conectará: quite la cubierta del enchufe, Vea Fig 5. 8. Lorsque le premier appareil d’éclairage est monté, vous pouvez installer l’appareil suivant de la chaîne.