Specification

Catalog Number
Notes Type
FEATURES & SPECIFICATIONS
INTENDED USE
Ideal for a wide variety of low- to medium-height ceiling applications including
commercial, retail and hospitality spaces where a baffled fixture is required.
CONSTRUCTION
Heavy gauge die formed galvanized steel mounting frame with mechanical trim
retention (yoke) ensures secure and flush reflector mounting to ceiling. Attached
to frame are vertically adjustable mounting brackets for use with C channels, ½”
steel conduit or 16 gauge flat bar hangers included, standard. Frames equipped
with galvanized junction box UL Listed for through wire applications. Junction
boxes equipped with (2) ¾” and (4) ½” conduit knockouts with pryout slots and
removable access doors.
Maximum 1-1/2” ceiling thickness.
OPTICS
Aluminum full reflectors are optically designed to maximize lumen output and to
provide superior glare control. The black or white baffled reflectors have a semi-
specular upper finish with white painted flange standard.
ELECTRICAL
Electronic ballast with end of lamp life protection standard. Class P thermally
protected ballast protects against improper contact with insulation. Minimum
starting temperature is 0°F/-18°C.
Rated for #12 AWG conductor thru-branch wiring. Minimum 90° supply wire.
Ground wire provided.
Lamp Socket Base:
DTT 4-pin lamps – 13W (G24Q-1); 18W (G24Q-2); 26W (G24Q-3)
LISTING
Fixtures are UL Listed for thru-branch wiring, Non-IC recessed mounting, damp
location, and to U.S. and Canadian Safety Standards.
Compact Fluorescent Downlighting
6” LF6N
BAFFLE
Horizontal, 2-Lamp Double Twin-Tube (DTT)
NOTES:
1 Not available with ADEZ or ECOS.
2 White painted flange standard.
3 Electronic multi-volt ballast capable of operating any line
voltage from 120-277V, 50 or 60Hz.
4 Not available with EL or ELR.
5 Ships standard for 1-lamp operation. For 2-lamp opera-
tion, consult installation instructions or factory. Add 3”
(7.6) to width and 4-1/2” (11.4) to length.
6 Not recommended for field installation.
7 One 5A relay with one 0-10 VDC dimming output, shipped
installed. Requires additional nLight bus power supply.
8 For additional options see lithonia.com.
Downlighting and Track Sheet #: LF6N-BAFFLE-2-DTT
All dimensions are inches (centimeters).
Specifications
Max. Height: 6-3/8 (16.2)
Ceiling Opening: 7 (17.8)
Overlap Trim: 7-1/2 (19.1)
Length: 13 (33.0)
Width: 11 (27.9)
For shortest lead times, configure product using standard options (shown in bold).
Example: LF6N 2/26DTT F6B3 MVOLT
ORDERING INFORMATION
Accessories
Order as separate catalog number
SCA6 Sloped ceiling adaptor. Degree of
slope must be specified (10D, 15D,
20D, 25D, 30D) Ex: SCA6 10D.
CTE6 Ceiling thickness extender is used
when ceiling thickness is greater
than 1-1/2 (3.8). Maximum thickness
2 (5.1).
6-3/8
(16.2)
7-1/2
(19.1)
11
(27.9)
13
(33.0)
6-3/8
(16.2)
6
(15.2)
7-1/2
(19.1)
Series
LF6N
Wattage/lamp
2/13DTT
1
2/18DTT
2/26DTT
Voltage
MVOLT
3
120
277
347
4
Options
8
ADEZ Advance Mark 10™ electronic dimming ballast, 120V or
277V. Must be wattage and voltage specific. Minimum
dimming level 5%
ECOS Lutron EcoSystem electronic dimming ballast, 120V - 277V.
Must be wattage specific. Minimum dimming level 5%
EL Emergency PSDL3 DL battery pack with integral
test switch.
5
ELR Emergency PSDL3 DL battery pack with remote
test switch
5
ELRHL2LP Iota I-162 Emergency battery pack with remote test
switch. Operates two 26W CFL lamps in emergency mode
with battery back-up in case of power disruption. Average
lumen output is 2600
6
GMF Single slow-blow fuse, must specify voltage
BDP Ballast disconnect plug (meets codes that require in-
fixture disconnect)
4
RIF1 Radio interference filter
LBH Less barhangers
NSD Sensor Switch nLight™ dimming relay
7
WLP 35K lamp (shipped separately)
Reflector/color
2
F6B3 Black baffle
F6B3W White baffle
LF6N