Installation Guide

ManualsBrandsLithonia Lighting ManualsLighting & Ceiling FansOutdoor Metal Halide Bronze Flood Light with Glass Lens

SAVE THESE INSTRUCTIONS

Rev B 01/17/12

RJ521319 INST SHT SMALL FLOOD CS

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

2007 © Acuity Lighting Group, Inc.

INSTALLATION

INSTRUCTIONS

RISK OF FIRE - Lamps are hot. Keep combus-

tible material away from hot parts.

TROUBLESHOOTING

CAUTION

If this ﬁ xture fails to operate properly,

check to make sure:

• The correct lamp is properly installed.

• The ﬁ xture is wired correctly.

• The lamp is not faulty.

• The ﬁ xture is grounded correctly.

• The line voltage at the ﬁ xture is correct.

Observe lamp manufacturer's recommendations and

restrictions on lamp operations, including but not

limited to ballast type, burning position, and cycling.

Use ANSI rated lamps only.

Maintenance: For optimum performance, periodically

clean reﬂ ector and lens with a soft, damp cloth.

Important: DO NOT use abrasive materials, glass

cleaner or other solvents on lens or paint. Use only

mild, soapy water.

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH,

INJURY, OR SIGNIFICANT PROPERTY DAMAGE

- For your protection, read and follow these warnings and

instructions carefully before installing or maintaining this ﬁ xture. These instructions do not attempt to cover all

installation and maintenance situations. If you do not understand these instructions or additional information is

required, contact Lithonia Lighting or your local Lithonia Lighting distributor.

WARNING: RISK OF ELECTRIC SHOCK - To avoid electric shock, serious injury, or death, be certain that all

electrical power is disconnected from the supply branch circuit conductors before installing or maintaining this

ﬁ xture. This product must be installed and maintained in accordance with the applicable installation codes by a

person familiar with the construction and operation of the product and the hazards involved.

WARNING: RISK OF PERSONAL INJURY - This product may have sharp edges. Wear gloves to prevent

cuts or abrasions when removing from carton, handling, installing and maintaining this product. Lithonia

Lighting assumes no responsibility for claims arising out of improper or careless installation or handling of this

product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

• Do not install a damaged ﬁ xture.

• This ﬁ xture must be wired in accordance

with the National Electrical Code and ap-

plicable local codes and ordinances.

• Proper grounding is required to ensure

personal safety. Be certain green lead from

the ﬁ xture is connected to supply ground.

• Use code compliant connectors for all

electrical connections.

• ALL work should be done by a qualiﬁ ed

electrician.

• WARNING: NEVER connect or discon-

nect any component while power supply is

engaged.

DELIVERY: Upon receipt of ﬁ xture and accessories

(packed separately), thoroughly inspect for any

freight damage. All damage should be reported

to the delivery carrier. Do not install damaged

ﬁ xtures. Compare the catalog description listed

on the packing slip with the ﬁ xture label on the

inside of the housing to be sure you have received

the correct merchandise.

IMPORTANT SAFETY

INSTRUCTIONS

Small Flood

INSTALLATION

LOCATION: The adjustable straight pipe thread knuckle can mounted to any metal 1/2”NPSM threaded

mounting. This ﬁ xture should not be mounted within 6” of any ﬂ ammable materials. This ﬁ xture is for

outdoor use and should not be used in areas with limited ventilation or high ambient temperatures. Fixture

should not be recessed.

JUNCTION BOX MOUNTING

1. Thread aiming arm through the cover plate (not included) and tighten the locknut provided.

2. Make supply connections (described below), attach the cover plate to the junction box. Fixture must be

oriented so that the lamp is base down.

CONDUIT MOUNTING

1. Secure appropriate conduit ﬁ tting (not included) to ﬂ oodlight knuckle.

2. Make supply connections (described below) and tighten ﬁ tting to conduit. Do NOT tighten ﬁ tting by rotat-

ing entire ﬁ xture in the desired position.

AIMING: Loosen the side bolt connected to the arm knuckle to aim the ﬁ xture up or down. Re-tighten bolt

to secure the ﬁ xture in the desired position.

WIRING

Caution: Check that voltage is compatible with ﬁ xture ballast (120, 208, 240, or 277V--factory wired to 277).

Use approved connectors for all electrical connections. Insulate all unused leads. Connect ﬁ xture to supply

wires rated for at least 90°C.

1. Connect the desired voltage lead from the ﬁ xture to the same voltage supply lead.

2. Connect the lead from the ﬁ xture labeled (COM) to the Common supply lead.

3. Connect the ground wire (green or bare copper wire) from the ﬁ xture lead to the ground supply lead.

LAMP INSTALLATION AND RE-LAMPING

1. When re-lamping, turn power off at the circuit breaker and allow the ﬁ xture to cool adequately.

2. Open the lens frame by unscrewing the two screws on the top of the ﬁ xture.

3. Install the correct lamp (provided). Prior to installing the lamp in the ﬁ xture, check to be sure the lamp is of

proper type and wattage. Screw the lamp securely into the socket, back the lamp out one to two turns, then

screws the lamp back in, making sure it is secure. This properly seats the lamp in the socket.

4. Close the door frame and tighten screws in original position. Do not overtighten the screws. Be sure that

the gasket is ﬁ rmly seated in the proper channel prior to closing ﬁ xture to maintain weather-tight seal.

5. Re-connect the power.

RISK OF FIRE - Observe lamp manufacturer’s warn-

ings, recommendations and restrictions on lamp

operation and maintenance.

WARNING