Specification

FEATURES & SPECIFICATIONS
INTENDED USE
The sleek design of the D-Series Size 1 Flood reflects the embedded high performance LED
technology. It is ideal for landscape, signage and accent lighting in many commercial and residential
applications.
CONSTRUCTION
Die-cast aluminum housing has integral heat sink fins to optimize thermal management through
conductive and convective cooling. The LED driver is mounted in direct contact with the casting
to promote low operating temperature and long life. Housing is completely sealed against
moisture and environmental contaminants using a tempered glass lens(IP66). Low EPA (0.6 ft
2
) for
optimized wind loading.
FINISH
Exterior parts are protected by a zinc-infused Super Durable TGIC thermoset powder coat finish
that provides superior resistance to corrosion and weathering. A tightly controlled multi-stage
process ensures a minimum 3 mils thickness for a finish that can withstand extreme climate
changes without cracking or peeling.
OPTICS
A variety of precision-molded vacuum-metallized specular reflectors are engineered for superior
target illumination, uniformity and spacing. Light engines are available in 3000K (70 CRI min.),
4000K (70 CRI min.) or 5000K (70 CRI min.) configurations. Optional visors offer additional
versatility.
ELECTRICAL
Light engine(s) consist of chip-on-board (COB) LEDs directly coupled to the housing to
maximize heat dissipation and promote long life (100,000 hrs, L80). Single-engine unit uses a
Class 2 electronic driver; dual-engine unit uses a Class 1 electronic driver. Both drivers have
a power factor >90%, THD <20%, and an expected life of 100,000 hours. Standard 6KV surge
protection meets a minimum Category C Low operation (per ANSI/IEEE C62.41.2).
INSTALLATION
Integral adjustable knuckle with 1/2-14NPS threaded pipe, tenon slipfitter, or integral
slipfitter, facilitates quick and easy installation to a variety of mounting accessories. This
secure connection enables the D-Series Size 1 to withstand up to a 1.5 G vibration load rating
per ANSI C136.31.
LISTINGS
CSA certified to U.S. and Canadian standards. Luminaire is IP66 rated. Rated for -40°C
minimum ambient.
DesignLights Consortium
®
(DLC) Premium qualified product and DLC qualified product. Not
all versions of this product may be DLC Premium qualified or DLC qualified. Please check
the DLC Qualified Products List at www.designlights.org/QPL to confirm which versions are
qualified.
WARRANTY
5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx.
Note: Actual performance may differ as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specifications subject to change without notice.
One Lithonia Way • Conyers, Georgia 30012 • Phone: [phone] • www.lithonia.com
© 2012-2016 Acuity Brands Lighting, Inc. All rights reserved.
DSXF1-LED
Rev. 11/14/16
Mounting, Options and Accessories
THK - Knuckle with 1/2” NPS
threaded pipe
IS – Integral sliptter
H= 2-1/2” (6.3 cm)
ID= 2-3/8” (6.0 cm)
OD= 3-1/2” (8.8 cm)
YKC62 - Yoke with SO cord
H= 4-1/4” (10.7 cm)
D= 2-1/4” (5.7 cm)
UBV – Upper/bottom visor
W= 5-1/4” (13.3 cm)
H= 2-1/2” (6.3 cm)
D= 3” (7.6 cm)
FV – Full visor
W= 5-1/4” (13.3 cm)
H= 2-1/2” (6.3 cm)
D= 3” (7.6 cm)
VG – Vandal guard
W= 6-1/2” (16.5 cm)
H= 4” (10.1 cm)