Specification

Catalog
Number
Notes
Type
DOWNLIGHTING 6BP LED
LED Recessed Downlighting
6BP
6” LED Module
IC/Non-IC
Retrot
FEATURES & SPECIFICATIONS
INTENDED USE — Our recessed LED module is the most economical means to create a well lit environment
with exceptional energy eciency and near zero maintenance. Great for retrot into existing downlight
cans or new construction and remodel applications. Unique torsion spring and friction clip retention
allows tment into nearly 100% of installed cans. The LED module maintains at least 70% light output
for 50,000 hours.
CONSTRUCTION — Aluminum die cast reector with deep bae conguration for reduced glare.
Combined LED and driver printed circuit board attached. Inner reector cone funnels light through the
pressed-in diused lens.
OPTICS — Diused lens at end of mixing chamber to provide even light distribution for general illumina-
tion, equivalent to 65W BR30 or 100W BR30 lamp.
Wide ood beam angle at >45°. Utilizes 3000 K color temperature LEDs. CRI - 83.
ELECTRICAL — Center 2 Edge™ (patent pending) technology created for a single point source. Primary
power disconnect provided for simple connection to a dedicated LED connector in the housing.
Dimming down to 15%. For compatible dimmers, refer to Compatible Dimmers Chart.
620-lumen P series has an input wattage of 8.9 watts, 70 lumens per watt, equivalent to 65-watt
incandescent.
P Series’ patent pending driver has zero inrush, which allows power loads to be calculated with actual
rated wattages.
Example: 67 units of 6BPMW LED xtures can be installed in line with a 600-watt dimmer. 600W/8.9W
= 67.4 xtures.
950-lumen P series has an input wattage of 15.2 watts, 63 lumens per watt, equivalent to 100-watt
incandescent.
*Actual wattage may dier by +/-5% when operating at 120V +/-10%.
INSTALLATION  Suitable for installation in standard and shallow-height rough-in sections.
E26 socket adapter and splice kit ships standard. This enables easy installation or permanent conversion
to an LED source for Title 24 compliance.
Twin torsion springs ensure easy installation.
Friction clips included to allow tment into cans without torsion brackets from an inside diameter of
6.0” to 7.0”.
LISTINGS — CSA certied to US and Canadian safety standards. ENERGY STAR® qualied; California
T24 compliant. Wet location listed for indoor use only. WSEC ASTM E283 for Air-Tight (with IC housings).
WARRANTY — 5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Specications subject to change without notice.
Patents pending.
6BPMW
Series/Finish Lamps/Lumens
1
Color temperature Voltage Options
6BP 6"
Bae LED
module
MW Matte white LED 8.9W, 620
lumens
HL LED 15.2W, 950
lumens
(blank) 3000 K (blank) 120V L7XLED T24
2
New Construction
Rough-In LED Base
L7XRLED T24
2
Remodel Rough-In
LED Base
LC6LED T24
2
New Construction
Rough-In LED Base
L7X
3
New construction
rough-in
L7XR
3
Remodel rough-in
L7XP
3
New construction shallow
rough-in
L7XPR
3
Remodel shallow rough-in
LC6
3
New construction rough-in
LCP
3
New construction shallow
rough-in
ORDERING INFORMATION
For shortest lead times, congure products using bolded options.
Example: 6BPMW LED L7XLED T24
Accessories: Order as separate catalog number.
TSA6 Makes non-bracket housing compatible with the LED
module; ships as units, J6 or J25
FL2LED Makes L7XF housings compatible with the LED module
Torsion mount shown
Friction clip shown
(included)
5-7/8
(14.9)
3-7/
8
(9.8)
7-7/8
(20.0)
Notes
1 Total system delivered lumens.
2 LED module ships less E26 adaptor and
hardwire kit.
3 Must be ordered on separate line.
Specications
Aperture: 5 7/8 (14.91)
Ceiling opening: as rough-in
Overlap trim: 7-5/8 (19.4)
Height: 3-7/8 (9.8)
All dimensions are inches (centimeters)
unless otherwise indicated.
E26 adaptor
(included)
Splice kit
(included)