Installation Guide
LED Recessed Downlighting
4BP/4OP
4” LED Module
IC/Non-IC
Retrot
FEATURES & SPECIFICATIONS
INTENDED USE — Our recessed LED module is the most economical means to create a well lit environ-
ment with exceptional energy eciency and near zero maintenance. Great for retrot into existing
downlight cans or new construction and remodel applications. Compliant friction clip retention allows
tment into nearly 100% of installed cans. The LED module maintains at least 70% light output for
50,000 hours.
CONSTRUCTION — Aluminum spun reector with deep bae conguration for reduced glare.
Combined LED and driver printed circuit board attached. Inner reector cone funnels light through the
pressed-in diused lens.
Bae and open trim inserts are available in multiple nishes.
OPTICS — Diused lens at end of mixing chamber to provide even light distribution for general illumina-
tion, equivalent to 65W BR30 Lamp.
Wide ood beam angle at > 45°.
ELECTRICAL — Center 2 Edge™ (patent pending) technology created for a single point source. Primary
power disconnect provided for simple connection to a dedicated LED connector in the housing.
Dimming down to 10%. For compatible dimmers, refer to Compatible Dimmers Chart.
P Series' patent pending driver has zero inrush which allows power loads to be calculated with actual
rated wattages.
Example: 53 units of 4BPMW LED xtures can be installed in line with a 600-watt dimmer. 600W/11.2W
= 53.5 xtures.
Standard input wattage is 11.2 watts or less; equivalent to 65-watt incandescent.
INSTALLATION — Suitable for installation in standard height rough-in sections.
E26 socket adapter (except in the state of California on 4BP xtures) and splice kit ships standard. This
enables easy installation or permanent conversion to an LED source for Title 24 compliance.
Friction clips allow tment into cans with an inside diameter of 4.0” to 4.5".
LISTINGS — CSA certied to US and Canadian safety standards. California T24 compliant. Wet location
listed for indoor use only. WSEC ASTM E283 for Air-Tight (with IC housings).
WARRANTY — 5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Actual performance may dier as a result of end-user environment and application.
All values are design or typical values, measured under laboratory conditions at 25 °C.
Specications subject to change without notice.
PATENTS PENDING.
Notes
1 Total system delivered lumens.
2 Must be ordered on a separate line.
3 This option must be selected for product
shipping to California.
DOWNLIGHTING 4BP4OP LED
E26 adaptor Splice kit
(included)
D
I
M
M
A
B
L
E
See trim inserts on page 2.
Specications
Aperture: 4.0 (10.2)
Ceiling opening: Determined by rough-in
Overlap trim: 5-1/4 (13.3)
Height: 3-11/16 (9.4)
All dimensions are inches (centimeters) unless otherwise indicated.
4
(10.2)
3
(7.6)
3-11/16
(9.4)
5-1/4
(13.3)
Catalog
Number
Notes
Type
ORDERING INFORMATION
Lead times will vary depending on options selected. Consult with your sales representative.
Example: 4BP TRMW LED 27K 90CRI
LED
Series/Finish Lamp CCT / CRI / W / Lumens
1
Voltage Options
4BPMW 4" Bae LED module, matte white
4BP TRMW 4" Bae LED module, black bae, matte white ange
4BPBN 4" Bae LED module, brushed nickel
4BPORB 4" Bae LED module, oil-rubbed bronze
LED (blank) 3000 K / 83CRI / 10.6W / 620L
27K 90CRI 2700 K / 93CRI / 11.2W / 600L
30K 90CRI 3000 K / 93CRI / 11.2W / 600L
40K 90CRI 4000K/95CRI/11.2W/650L
(blank) 120V L3LED T24 New construction rough-in LED base
L3RLED T24 Remodel rough-in LED base
L3 New construction rough-in
2
L3R Remodel rough-in
2
L/SKTWHIP No E26 Adapter (CA only)
3
4OPA 4" Open LED module, clear diuse
4OPAZ 4" Open LED `module, clear specular
4OPA TRMW 4" Open LED module, clear diuse, matte white ange
4OPAZ TRMW 4" Open LED module, clear specular, matte white ange
LED (blank) 3000 K / 83CRI / 10.6W / 620L
27K 90CRI 2700 K / 93CRI / 11.2W / 600L
30K 90CRI 3000 K / 93CRI / 11.2W / 600L
40K 90CRI 4000K/95CRI/11.2W/650L
(blank) 120V L3LED T24 New construction rough-in LED base
L3RLED T24 Remodel rough-in LED base
L3 New construction rough-in
2
L3R Remodel rough-in
2
TRIM INSERTS (for eld conguration; ordered separately)
Series/Finish Packaging
4BP TRMW 4" Bae black, matte white ange insert
4BPBN 4" Bae brush nickel insert
4BPORB 4" Bae oil-rubbed bronze insert
4OPA 4" Open clear diuse insert
4OPAZ 4" Open clear specular insert
4OPA TRMW 4" Open clear diuse, matte white ange insert
4OPAZ TRMW 4" Open clear specular, matte white ange insert
R12 Retail pack
of 12 units
U Unit
Example: 4BPBN R12
Accessories: Order as separate catalog number.
RK1 CG52178 E26 ADAPTER/MALE PLUG BAL DISC ASM E26 Adapter