READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Model: WH44OSB5L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pgs. 3 - 4 Wiring. pg. 4 Fan Assembly. pg. 5 Motor Housing Assembly. pg. 5 Blade Assembly. pg. 6 Light Kit Assembly (Optional). pgs. 6 - 7 Testing Your Fan. pg. 8 Troubleshooting. pg. 9 Parts Replacement. pg. 9 Warranty. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b a. hanging bracket. 1 piece b. motor housing. 1 piece c. motor assembly. 1 piece c d. blade arm. 5 pieces d e. blade. 5 pieces f. light kit fitter.
3. Installation Preparation. 10ft. - 12ft. (3.05m - 3.66m) blade edge To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 144 square feet (13.4 square meters). 30 inches 7 feet (76cm) (2.13m) 10ft. - 12ft. (3.05m - 3.
4. Hanging Bracket Installation. (cont.) Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box.* Pull electrical wiring from outlet box through center hole in the hanging bracket. hanging bracket *NOTE: It is very important that you use the proper hardware when installing the hanging bracket as this will support the fan. spring washers flat washers outlet box screws 5. Wiring.
. Fan Assembly. Remove motor assembly from j-hook on hanging bracket. Lift motor assembly to hanging bracket and carefully push wiring and wire connectors into outlet box. Align holes in top of motor assembly with bolts in hanging bracket and push up so that bolts come through holes. Secure motor assembly with flat washers and motor mounting nuts that were previously removed (refer to page 3, Section 4).
8. Blade Assembly. Locate fifteen 3C-Clips™ in one of the hardware packs. Hold a blade arm up to a blade and align the preassembled blade screw posts on the blade arm with the holes on the blade. [NOTE: Make sure to attach blade arm so the flat side of the blade faces UP.] motor housing Press on blade firmly until blade screw posts come through holes in blade and then slide a 3C-Clip onto each blade screw post. PLEASE NOTE WARNINGS BELOW when attaching 3C-Clips.
9. Light Kit Assembly (Optional). (cont.) switch housing cap Locate BLACK (or BLUE) and WHITE wires in switch housing labeled "LIGHT." Remove and discard plastic that holds these 2 wires together. hex nut lock washer threaded rod center cap light kit fitter Remove hex nut and lock washer from threaded rod at top of light kit fitter. Punch center cap out of switch housing cap with a screwdriver. Feed wires (one by one) from light kit fitter through center hole in switch housing cap.
10. Testing Your Fan. It is recommended that you test fan before finalizing installation. Restore power from circuit box and light switch (if applicable). Test fan speeds with the pull chain on switch housing located to the RIGHT of the reverse switch (labeled FAN). Start at the OFF position (no blade movement). First pull will set the fan to HI. Second pull will set the fan to MEDIUM. Third pull will set the fan to LOW. Fourth pull will again set the fan to OFF setting.
Troubleshooting. Warranty. Problem: Fan fails to operate. Solutions: 1. Check wall switch to fan. 2. Verify that reverse switch is set completely in either direction. 3. Check to be sure fan is wired properly. Problem: Light kit (optional) not lighting. Solutions: 1. Check wall switch to fan. 2. Check that bulbs are installed correctly. 3. Verify that wires in outlet box are wired properly. 4. Verify that molex connections in switch housing are connected properly.
