READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Models: UB48BC4L UB48WW4L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pg. 4 Wiring. pg. 5 Canopy Assembly. pg. 6 Blade Assembly. pg. 6 Light Kit Assembly. pg. 7 Testing Your Fan. pg. 7 Troubleshooting. pg. 8 Parts Replacement. pg. 8 Warranty. pg. 8 4009654 net weight of fan: 13.66 lb (6.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a a. hanging bracket. 1 piece b. blade. 4 pieces b c. motor housing, downrod and canopy (pre-assembled). 1 piece c d. glass shade. 1 piece e.
3. Installation Preparation. blade edge 12ft. - 15ft. (3.66m - 4.57m) To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 10ft. (3.05m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 225 square feet (20.9 square meters). 30 inches 10 feet (76cm) (3.05m) 12ft. - 15ft. (3.66m - 4.57m) This fan can be mounted with a downrod on a normal ceiling only.
. Fan Assembly. With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Loosen canopy set screw and lower canopy to expose hanging ball at top of downrod. Remove plastic from end of safety cable. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on hanging bracket. Turn hanging ball until slot lines up with hanging bracket tab.
. Wiring. WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. white supply wire black supply wire from ceiling black white Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
. Canopy Assembly. Raise canopy to hanging bracket until canopy touches the ceiling. Tighten the canopy set screw to secure canopy. Carefully remove protective paper from downrod. canopy canopy set screw downrod 8. Blade Assembly. Remove protective film from both sides of blade. Locate one of the rubber cushions on top of motor housing. Remove the 2 larger screws (do not remove center screw) and washers but leave rubber cushion intact.
9. Light Kit Assembly. Install one 6.5 watt medium base LED bulb (included). IMPORTANT: When replacing bulb, please allow bulb and glass shade to cool before touching. reverse switch Partially loosen 3 thumbscrews at bottom of motor housing and raise glass shade to motor housing. Secure glass shade with thumbscrews. Be sure thumbscrews make contact with rubber ring on glass shade, but do NOT overtighten thumbscrews as glass may crack or break. motor housing thumbscrew bulb 10. Testing Your Fan.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LITEX 15-YEAR LIMITED WARRANTY: LITEX INDUSTRIES, LTD. warrants this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or repair any fan which has faulty performance due to a defect in material or workmanship.
