READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Installation Guide For Models: SG52BNK5L SG52EB5L Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pg. 6 Canopy Assembly. pg. 6 Blade Assembly. pg. 7 Light Kit Assembly (Optional). pgs. 7- 8 Testing Your Fan. pg. 8 Troubleshooting. pg. 9 Parts Replacement. pg. 9 Warranty. pg. 9 4007498 net weight of fan: 16.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b c d a. canopy. 1 piece b. hanging bracket. 1 piece c. downrod and hanging ball (with pin and clip). 1 piece d. motor housing. 1 piece e e.
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 30 inches 7 feet (76cm) (2.13m) This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling. The hanging length can be extended by purchasing a longer downrod (0.5in./1.27cm diameter).
. Fan Assembly (with downrod). If you wish to extend the hanging length of your fan, you must remove the hanging ball from the downrod provided to use with an extended downrod (sold separately). [If you wish to use the downrod provided, please proceed to instructions following the dotted line below.] To remove hanging ball, loosen set screw on hanging ball and remove pin and clip. Lower hanging ball and remove stop pin.
5. Fan Assembly (with downrod). (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan. Grab the fan firmly with two hands. Slide downrod through opening in hanging bracket and let hanging ball rest on the hanging bracket. Turn the hanging ball slot until it lines up with the hanging bracket tab.
. Wiring. WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. white supply wire ground (green or bare) black supply wire CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. from ceiling Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
9. Blade Assembly. motor housing Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades. Locate 15 blade attachment screws and washers in one of the hardware packs. Hold blade arm up to blade and align holes. Insert 3 blade attachment screws (along with washers) with fingers first and then tighten screws securely with a Phillips screwdriver. Repeat for the remaining blades.
10. Light Kit Assembly (Optional). (cont.) Connect WHITE wire from switch housing to WHITE wire from light kit fitter. Connect BLUE (or BLACK) wire from switch housing to BLACK wire from light kit fitter. Be sure molex connections snap together completely. Align holes in light kit fitter with holes in switch housing. (Note: The gap on the top edge of the switch housing cap must align with the reverse switch on the switch housing for the proper fit.
Troubleshooting. Warranty. Problem: Fan fails to operate. Solutions: 1. Check wall switch to fan. 2. Verify that reverse switch is set completely in either direction. 3. Check to be sure fan is wired properly. Problem: Light kit (optional) not lighting. Solutions: 1. Check wall switch to fan. 2. Check that bulbs are installed correctly. 3. Check to be sure wires in canopy are wired properly. 4. Verify that molex connections are connected properly in switch housing.
